Store relaunching soon · pro diagnostics & tools for independent shopsjoseph@directtoolsource.com
Direct Tool SourcePro Diagnostics
Home / Answers / OBD-II & Trouble Codes / Control Module, Power and Charging Codes

Control Module, Power and Charging Codes

Codes that point at control module memory, programming, power relays, reference voltages and charging system control.

9 answers · last reviewed 2026-11-16

What does P0601 internal control module memory checksum error mean?

Short answer: The control module found that its stored software failed a self-check, which may mean corrupted programming or an internal fault; reprogramming fixes some cases, and others need a new module.

Control modules regularly verify their software with a checksum. If the calculated value does not match the expected value, the module sets P0601. Causes can include an interrupted programming event, voltage spikes, or a failing memory chip inside the module.

Check service bulletins first, since some vehicles have known software issues with a reprogramming fix. Verify the module's power and ground circuits and battery condition, because poor power can cause memory errors.

If the bulletins and circuits check out, reprogram the module with the vehicle maker's software and a stable power supply connected. If the code returns after a successful programming session, the module itself is likely faulty. Replacement modules usually need programming and setup, so plan for that in the estimate.

Tools used for this job

Topdon RLINKJ2534 RLink J2534 OEM Pass-Thru ToolTopdon T1200005 120A Stable Power Supply & 12V Battery Charger

What do P0602 and P0603 control module codes mean?

Short answer: P0602 indicates a control module programming error, often meaning the module was not programmed or setup is incomplete, and P0603 indicates a keep-alive memory error, often linked to power supply problems.

P0602 typically appears when a module has not been programmed with the correct software or configuration, such as a new module that was installed without programming or a programming session that did not finish. The fix is to complete programming and any required setup with the vehicle maker's procedure.

P0603 points to keep-alive memory, which stores learned values like fuel trims and idle adaptations. The module may lose that memory if its constant power feed is interrupted. Check the battery, battery terminals, fuses and the constant power and ground circuits for the module.

For both codes, check service bulletins, and connect a programming power supply before any reflash. If P0603 keeps returning with good power and ground, the module itself may need replacement.

Tools used for this job

Topdon RLINKLITE RLink Lite J2534 Pass-Thru Programming DeviceClore Automotive PL6850 12/24V 120/40/10A Flashing Power Supply and Charger

What does P0685 ECM or PCM power relay control circuit mean?

Short answer: The engine computer detected a fault in the circuit that controls its main power relay, often from a bad relay, a wiring or fuse problem, or poor grounds.

Many engine computers control a main relay that powers the computer and related components when the ignition is on. P0685 means the computer saw something wrong with that control circuit, such as an open or short. Symptoms can include no start, intermittent stalling, or the computer staying powered after shutdown.

Find the relay and wiring in service information. Check related fuses, test the relay, and check voltage and ground at the relay socket with the ignition on. Inspect connectors for corrosion and loose terminals, and check the computer's grounds.

Relay test jumpers allow you to check circuits with the relay removed. Use fused jumpers, and do not bypass a relay without understanding what circuits it powers, since that can damage modules.

Tools used for this job

Lisle 56810 Relay Test Jumper KitLisle 28800 Digital Test Light with Load Tester

What does P0620 generator control circuit mean?

Short answer: The engine computer found an electrical fault in the circuit it uses to control the alternator, often from wiring, connector or alternator regulator problems.

On many vehicles, the engine computer controls alternator output through a control circuit rather than letting the alternator regulate itself completely. P0620 means the computer saw something wrong with that circuit, such as an open or short. Related codes like P0622 point to the generator field circuit.

Start with a charging system test: battery voltage at rest, voltage with the engine running, and voltage under load. Inspect the alternator connector and wiring for corrosion or damage. Check service information for how the control signal should look and test it with a meter or scope.

Some vehicles use a battery current sensor and smart charging strategy, so charging voltage changes normally. Check battery condition first, since a failing battery can confuse diagnosis. Keep hands clear of belts and fans while testing on a running engine.

Tools used for this job

Electronic Specialties 726 Digital Battery & Electrical System Analyzer w/PrinterAutel MP608

What does P0532 or P0533 A/C refrigerant pressure sensor circuit mean?

Short answer: P0532 means the A/C pressure sensor signal is too low and P0533 means it is too high, usually from a sensor, wiring or connector problem, though actual system pressure can play a role.

The A/C pressure sensor on the high side reports refrigerant pressure so the computer can control the compressor and cooling fans. P0532 sets when the signal voltage is lower than expected, and P0533 when it is higher. The A/C may not work because the computer protects the system when it cannot trust the reading.

Compare the sensor reading in live data with a gauge set connected to the service ports. If they match, the sensor is accurate and the system pressure may be the issue. If they disagree, check the sensor's reference voltage, ground and signal at the connector.

Shorts and opens in the wiring are common, as are corroded connectors near the front of the vehicle. Wear eye protection and gloves when connecting gauges, and keep hands clear of fans that may start without warning.

Tools used for this job

Mastercool 99935 R134A & R1234YF Smart Manifold Gauge Set with 72" R134a hosesFluke 1567573 TP40 Automotive Back Probe Pin Set

What does P0563 system voltage high mean?

Short answer: The engine computer measured system voltage above its normal range, usually from an overcharging alternator or a charging control problem, though a poor computer ground can also cause it.

The engine computer monitors system voltage at its power input. P0563 sets when voltage stays above the limit. High voltage can damage modules and batteries, and may cause bulbs to burn out or warning lights.

Measure battery voltage with the engine running at idle and at higher rpm, and compare with the specification. If voltage is high, check the alternator regulator, the charging control circuit, and any battery current or temperature sensor the vehicle uses.

If battery voltage is normal but the computer still reports high voltage, check voltage drop on the computer's ground circuits. Keep hands clear of belts and fans while testing on a running engine.

Tools used for this job

Electronic Specialties 726 Digital Battery & Electrical System Analyzer w/PrinterAutel BT508 Bluetooth Battery and Electrical System Analysis

What does code P0615 mean?

P0615 means a problem in the starter relay control circuit, usually from a failed relay, wiring fault or poor connection; check the relay and its control circuit.

Read the full answer →

What does code P0645 mean?

P0645 means a fault in the A/C compressor clutch relay control circuit; check the relay, the wiring and the engine computer's control of the relay.

Read the full answer →

What does code P0571 mean?

P0571 means a problem in the brake switch A circuit, which can disable cruise control and affect other systems; check the brake switch adjustment, the switch itself and its wiring.

Read the full answer →

General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.