Store relaunching soon · pro diagnostics & tools for independent shopsjoseph@directtoolsource.com
Direct Tool SourcePro Diagnostics
Home / Answers / Hand Tools / Measuring Tools

Measuring Tools

Calipers, micrometers, feeler gauges, dial indicators and other precision measuring tools used in automotive repair.

5 answers · last reviewed 2026-11-16

What measuring tools should every technician own?

A good starting set is a digital or dial caliper, a set of feeler gauges, a tape measure, a tread depth gauge, and a dial indicator with a magnetic or flexible base for runout checks.

Read the full answer →

How do I use a feeler gauge correctly?

Short answer: Slide the blade between the parts with light, consistent drag, try the next sizes up and down to confirm, and keep blades clean and straight for accurate readings.

A feeler gauge measures a gap by finding the blade that fits with slight drag. Too loose means the gap is bigger; if the blade binds, the gap is smaller. The right feel takes practice, so compare readings by trying blades a size above and below.

Keep the blade flat and square to the gap. Twisting or angling it gives a false reading. Wipe blades clean before use, and replace bent or kinked blades, since a damaged blade does not measure accurately.

Use the correct type for the job. Straight blades suit flat gaps, and angled or long blades reach tight places. Go/no-go feeler gauges speed up quick checks within a set range. Lightly oil steel blades before storage to prevent rust.

Tools used for this job

Lisle 67950 15 Blade Standard Feeler GageLisle 68150 Go-No-Go Feeler GaugeCTA Tools A311 12" Long Feeler Gauge Set

How do I measure tire tread depth accurately?

Short answer: Measure in the main grooves at several points across the tread and around the tire, avoiding wear bars, and record the lowest reading for the inspection.

Tread depth tells you how much life a tire has left and whether it wears evenly. Use a tread depth gauge rather than a coin for a precise number. Measure in the main grooves on the outer, center and inner tread, and at several points around the tire.

Avoid measuring on the raised wear bars in the grooves, which give a false shallow reading. Compare inner, center and outer readings. A big difference points toward alignment or inflation problems.

Record the lowest reading on the inspection, since that determines replacement. Show customers the readings with photos when you recommend tires. Keep the vehicle secured with wheel chocks or safely on a lift when measuring, and never reach under a vehicle supported only by a jack.

Tools used for this job

S&G Tool Aid 65140 Tire Tread Depth GageAutel TBE200

How is a straightedge used in engine work?

Short answer: A precision straightedge and feeler gauges check cylinder heads, engine blocks and other machined surfaces for warpage before reassembly.

Head gaskets seal between two flat surfaces. If a cylinder head or block deck is warped, the new gasket may leak. To check, place a precision straightedge across the clean surface in several directions: lengthwise, crosswise and diagonally.

Slide feeler gauges under the straightedge at each position. The thickest gauge that fits shows the amount of warpage at that point. Compare with the engine maker's specification.

Clean surfaces thoroughly before measuring, since gasket residue gives false readings, and do not use abrasive pads that the engine maker prohibits on aluminum surfaces. Store the straightedge carefully so it stays straight. If warpage exceeds the limit, the surface needs machining or replacement.

Tools used for this job

Central Tools 6429 24" Straight EdgeGEARWRENCH 161D Deluxe Feeler Gage Set

How do I zero and check a caliper before measuring?

Short answer: Clean the jaws, close them gently and set zero, then check against a gauge block or known standard; recheck zero during a session and replace the battery on digital calipers when readings drift.

A caliper is only as good as its zero. Dirt between the jaws, a low battery on a digital caliper, or a drop can all throw readings off.

Wipe the jaws clean, close them with light, steady pressure and set the display or dial to zero. Then measure a gauge block or other known standard to confirm accuracy. If it reads wrong, clean and rezero. A caliper that still reads wrong should be repaired or replaced.

Measure with consistent light pressure and square to the part. Use the correct jaw surfaces for outside, inside and depth measurements. Store the caliper in its case, and keep it away from magnets and coolant.

Tools used for this job

Central Tools 3C301 Digital Caliper 0-6"/0-150mm

General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.