Hammers, Punches and Chisels
Choosing and using hammers, punches, chisels and drifts safely in automotive work.
What is a dead blow hammer used for?
Short answer: A dead blow hammer has a head partly filled with shot that reduces rebound, so it delivers a solid blow without bouncing back, which is useful for seating parts and freeing stuck components.
When a regular hammer hits a part, much of the energy bounces back. A dead blow hammer's head contains loose shot or sand that shifts on impact, damping the rebound and putting more energy into the part. Its plastic or rubber-covered face also reduces marking.
Technicians use dead blow hammers to free stuck brake rotors, knock suspension parts loose, seat components, tap parts into alignment, and drive tools such as pullers or punches when a softer face is wanted.
Choose a weight that fits the work. Small ones suit trim and alignment, and heavy ones suit suspension work. Wear safety glasses, check that nothing is behind the part that could be damaged, and keep hands and fingers out of the path of the blow.
Tools used for this job
Why should punches and chisels with mushroomed heads be dressed or replaced?
Short answer: A mushroomed head can shed sharp metal chips when struck, which can cause eye and hand injuries; grind the head back to a clean bevel or replace the tool.
Repeated hammer blows spread the striking end of a punch or chisel into a mushroom shape. The rolled-over edges are work-hardened and brittle. A hammer blow can break off a sliver that flies with enough speed to cut skin or injure an eye.
Inspect punches and chisels before use. If the head has spread, grind it back to a smooth chamfer, keeping the tool cool while grinding so the temper is not ruined. Replace tools with cracked heads or bent shanks.
Always wear safety glasses when striking tools, and keep other people out of the line of fire. Use a hammer of appropriate weight, and hold the punch firmly or use a punch holder to keep hands out of the way.
Tools used for this job
When should I use a brass hammer or brass punch?
Short answer: Use brass when you need to strike hardened parts without marring or damaging them, such as axle shafts, bearings and machined surfaces, since brass is softer than steel.
Striking a hardened steel part with a steel hammer can chip the part, mushroom its surface, or throw fragments. Brass is softer, so it deforms instead of the part. That makes brass hammers and drifts the right choice for driving axle shafts, tapping bearings and races into place, or loosening machined parts.
Brass tools wear with use. Dress or replace them when the faces become badly deformed, since a mushroomed brass punch can still throw pieces.
Wear safety glasses, hold punches firmly or with a holder, and keep others out of the way when striking. Use the right size drift so the force goes where you intend.
Tools used for this job
What is a ball peen hammer used for in a shop?
Short answer: A ball peen hammer is a general shop hammer for striking punches and chisels, shaping metal and peening rivets, with a flat face for striking and a rounded peen for shaping.
The ball peen hammer is the traditional machinist's and mechanic's hammer. Its flat face drives punches and chisels and handles general striking. The rounded peen end shapes sheet metal, sets rivets, and rounds over edges.
Choose a weight suited to the task. Lighter hammers work for small punches and precise taps, and heavier ones drive larger punches and chisels. A good handle with a secure head is essential.
Never strike two hardened steel hammer faces together, since chips can fly. Inspect hammer faces for cracks or chips and replace damaged hammers. Wear safety glasses whenever striking.
Tools used for this job
How do I use a punch to drive out a roll pin?
Short answer: Choose a pin punch that matches the roll pin diameter, support the part solidly, start the pin with a starter punch if needed, then drive it straight out with controlled hammer blows.
Roll pins and solid pins hold many parts together, from linkages to steering components. A pin punch has a straight shank so it can follow the pin through the hole. A starter punch with a tapered shank is stronger and starts a tight pin moving.
Support the part on a solid surface with a gap behind the pin so it has room to exit. Make sure the punch is straight in line with the pin. Use firm, controlled blows. Using a punch that is too small can bend it or let it slide into the pin's hollow center.
Wear safety glasses, keep fingers out of the way using a punch holder if needed, and replace bent or mushroomed punches. Use new roll pins on reassembly when the original is damaged.
Tools used for this job
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.