Store relaunching soon · pro diagnostics & tools for independent shopsjoseph@directtoolsource.com
Direct Tool SourcePro Diagnostics
Home / Answers / OBD-II & Trouble Codes / Fuel and Air Metering Codes

Fuel and Air Metering Codes

Rich and lean codes, MAP, IAT, throttle and boost codes: what they mean and how to test.

24 answers · last reviewed 2026-11-16

What does P2279 intake air system leak mean?

Short answer: The engine computer believes unmetered air is entering the intake after the airflow sensor; common causes are cracked intake ducts, leaking gaskets, PCV problems or a stuck-open valve.

P2279 appears when airflow calculations do not match what the computer expects, usually because air is leaking into the intake downstream of the mass airflow sensor. Fuel trims often run positive, especially at idle.

Look for cracked or loose intake ducts between the airflow sensor and throttle, leaking intake manifold or throttle body gaskets, disconnected vacuum hoses, and PCV valve or hose problems. On some engines a crankcase ventilation leak, an oil filler cap that does not seal, or a loose dipstick can contribute.

A smoke machine is the fastest way to find intake leaks. Seal the intake and fill it with smoke, then look for smoke escaping. Check service bulletins too, as some engines have known intake or PCV issues. Keep hands away from moving belts and hot exhaust parts during testing.

Tools used for this job

Thinkcar 310010006 PLD212 EVAP Smoke MachineMastercool 43066 Digital Dual Smoke Machine

What does P2101 throttle actuator control motor circuit range or performance mean?

Short answer: The engine computer detected that the electronic throttle motor is not moving the throttle as commanded, often from a dirty or failing throttle body, wiring problems, or low voltage.

Electronic throttle bodies use a motor driven by the engine computer and two position sensors that report where the throttle plate actually is. P2101 means the commanded and actual positions did not match the way the computer expected, or the motor circuit behaved abnormally. Many vehicles also enter a reduced power mode.

Check system voltage and battery condition first, since low voltage can cause throttle faults. Inspect the throttle body for carbon buildup that makes the plate stick. Check the connector for corrosion or loose pins, and wiggle test the harness while watching throttle position data.

Use a scan tool to compare commanded and actual throttle position. Clean the throttle body only as the vehicle maker allows, then perform any required throttle relearn. Disconnect the battery or keep the ignition off as directed, and never put fingers in the throttle bore, since the plate can close with force.

Tools used for this job

Autel MS906MAX OBDII Bi-Directional Diagnostic ScannerLisle 28800 Digital Test Light with Load Tester

What does P2138 throttle or pedal position sensor D/E voltage correlation mean?

Short answer: The two sensors in the accelerator pedal assembly disagree with each other, often from a failing pedal assembly, a wiring or connector problem, or a reference voltage issue.

Most accelerator pedals have two position sensors, often labeled D and E. The engine computer compares them constantly. If their voltages do not track together the way they should, the computer sets P2138 and usually limits power, since it cannot trust the driver's request.

With a scan tool, graph both pedal sensors while slowly pressing the pedal from rest to wide open. They should change smoothly, without dropouts. A glitch in one trace at the same pedal position each time points to the pedal assembly. Glitches that appear when you wiggle the harness point to wiring.

Check the 5 volt reference and ground circuits at the pedal connector, since a shared reference problem can affect other sensors too. Inspect for water intrusion or corrosion. Test with the engine off and the vehicle secured, and do not run the engine at high rpm in the bay.

Tools used for this job

Autel 906MAXMP608 MaxiSYS MS906 MAX & MaxiScope MP608 Oscilloscope BundleFluke 1567573 TP40 Automotive Back Probe Pin Set

What does P0121 throttle position sensor A circuit range or performance mean?

Short answer: The throttle position sensor signal does not match what the computer expects for other inputs, such as airflow and the second throttle sensor, often from a worn sensor, dirty throttle body or wiring.

P0121 is a plausibility code. The computer compares throttle position sensor A against other data, including the second throttle sensor on electronic throttles, airflow and manifold pressure. When the values do not agree, it sets the code and may limit power.

Graph both throttle position sensors with a scan tool or scope while operating the throttle smoothly. Look for dropouts, flat spots or noise in one signal. Check the reference voltage and ground at the connector, and wiggle the harness while watching data.

On electronic throttle bodies, the sensors are usually built into the throttle body, so a faulty sensor often means replacing the assembly and performing a throttle relearn. Disconnect the battery or keep the ignition off when the procedure requires it, and keep fingers out of the throttle bore.

Tools used for this job

Autel 906MAXMP608 MaxiSYS MS906 MAX & MaxiScope MP608 Oscilloscope BundleFluke 1567573 TP40 Automotive Back Probe Pin Set

What does P2004 intake manifold runner control stuck open bank 1 mean?

Short answer: The computer commanded the intake runner control to close but sensed it stayed open, commonly from a failed actuator, broken linkage, carbon buildup, or vacuum supply problems.

Many engines use intake manifold runner control valves to change airflow at different speeds. The computer commands them with an electric or vacuum actuator and watches position feedback. P2004 means the computer saw the runners stay open when commanded closed.

Inspect the actuator, linkage and connectors. Broken linkage arms and seized shafts are common. On vacuum systems, check the vacuum supply hose and solenoid. Use a scan tool to command the valve and watch the position feedback.

Carbon buildup can stop runners from moving, especially on direct injection engines. Check service bulletins, as some engines have known issues and specific repair kits. Turn the engine off and let it cool before working near the intake and exhaust manifolds.

Tools used for this job

Autel MS906MAX OBDII Bi-Directional Diagnostic ScannerOTC 6975 Vacuum/Pressure System Tester

What does P0201 injector circuit open cylinder 1 mean?

Short answer: The engine computer detected an open or fault in the injector control circuit for cylinder 1, often from a failed injector coil, a broken wire, or a connector problem.

Each fuel injector is controlled by the engine computer, which monitors the circuit. P0201 means the computer saw an electrical problem in the cylinder 1 injector circuit. Cylinder 1 will usually misfire because the injector is not firing.

Check the injector connector and harness for damage. Measure injector resistance and compare with the specification. A noid light shows whether the computer is pulsing the circuit, and a current probe shows whether the injector coil draws current normally.

On direct injection engines, injector circuits use much higher voltage, so do not use a noid light and follow the vehicle maker's test procedure. Relieve fuel pressure before removing injectors, keep sparks away and wear eye protection.

Tools used for this job

Lisle 27800 Universal Noid Light Adjustable Probes AllElectronic Specialties 687 Low Current Probe Digital Multimeter

What does P0108 MAP sensor circuit high mean?

Short answer: The manifold absolute pressure sensor signal voltage is higher than normal, often from an open ground, a signal wire shorted to the reference voltage, a failed sensor, or a disconnected vacuum hose.

The MAP sensor reports intake manifold pressure. With the engine running, it normally shows lower pressure than atmosphere. P0108 means the signal voltage is above the expected range.

With the key on and engine off, the MAP reading should match barometric pressure. With the engine running, it should drop. If it stays high, check the vacuum hose to the sensor if it has one, then check the sensor's reference voltage, signal and ground at the connector.

An open ground can make the signal read high. A signal wire shorted to the 5 volt reference also reads high. Compare with a vacuum gauge to confirm actual manifold vacuum. Keep hands clear of moving engine parts during testing.

Tools used for this job

Lisle 20300 Vacuum Gauge and Fuel Pump TesterFluke 1567573 TP40 Automotive Back Probe Pin Set

What does P0236 turbocharger boost sensor A circuit range or performance mean?

Short answer: The boost pressure sensor reading does not agree with expected values or other sensors, often from a failing sensor, a boost leak, a wiring problem, or a turbocharger control issue.

The boost sensor measures pressure in the intake after the turbocharger. P0236 means its reading is not plausible, for example not matching barometric pressure at key on, or not tracking with other sensors and engine conditions.

With the engine off and key on, the boost sensor should read close to barometric pressure. Compare it with the barometric or MAP sensor. If it disagrees, test the sensor's reference voltage, ground and signal.

If the sensor reads correctly at rest, look at actual boost during a road test. Boost leaks, a sticking wastegate or a variable vane problem can cause readings the computer considers out of range. Smoke testing the intake under pressure finds leaks. Let the turbo and exhaust cool before working near them.

Tools used for this job

Lisle 69910 14 Piece Turbo Test Kit With Smoke AdapterAutel MS906MAX OBDII Bi-Directional Diagnostic Scanner

What does code P0506 mean?

P0506 means the idle speed is lower than the engine computer expects; common causes include a dirty throttle body, intake restriction, vacuum leaks and heavy accessory loads.

Read the full answer →

General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.