A/C Service Equipment
Recovery machines, analyzers, leak detectors, couplers and other A/C service tools.
How do I remove and inspect an orifice tube?
Short answer: Recover the refrigerant, open the line at the orifice tube location, and use an orifice tube removal tool to pull it straight out; inspect the screen for debris that points to compressor wear.
Orifice tube systems use a small tube with a filter screen as the metering device, usually located in the liquid line or at the evaporator inlet. Recover the refrigerant first. Then disconnect the line and use an orifice tube removal tool, which grips the tube's tabs and pulls it out straight without breaking it.
The screen tells a story. Fine metal flakes suggest compressor wear. Black sludge suggests overheated oil or a failing compressor. Other debris may come from seals or a failed component. Heavy debris means you need to address the source and follow the flushing procedure.
If the tube breaks during removal, extraction tools can remove the broken piece. Install the correct new orifice tube with new O-rings lubricated with the right oil. Wear eye protection and gloves when opening refrigerant lines.
Tools used for this job
What are A/C block-off fittings used for?
Short answer: Block-off fittings seal individual sections of an A/C system so you can pressure test or isolate a section to find a leak or confirm a component before replacing it.
When a leak is hard to find, you can isolate the system into sections. Block-off fittings cap the ends of lines or component ports. With a section sealed, you can pressure test that part alone with a regulated test gas or vacuum and watch for pressure loss.
This approach helps confirm whether a leak is in the evaporator, condenser or a particular hose before taking apart the dash or replacing an expensive component. Block-offs are also handy to keep debris and moisture out of open lines during long repairs.
Use the correct fitting size and type for the connection. Kits come in metric and SAE, as well as union kits for repairing lines. Never pressurize beyond the test pressure in service information, use a regulator, and wear eye protection when testing pressurized sections.
Tools used for this job
How do I pressure test an A/C system with nitrogen?
Short answer: With the system recovered, connect a regulated dry nitrogen supply, pressurize to the value in service information, isolate the gauge and watch for pressure drop, then find leaks with bubble solution or an ultrasonic tool.
Nitrogen testing finds leaks without releasing refrigerant. Dry nitrogen also contains no moisture, so it will not contaminate the system. Recover all refrigerant first. Connect a nitrogen cylinder through a regulator and hose to the service port.
Raise the pressure slowly to the test value in service information and close the valve. Watch the gauge for a drop over time, keeping in mind that temperature changes also change pressure. Spray suspected areas with a leak detection solution and look for bubbles. Some technicians add a small amount of tracer gas so an electronic detector can be used.
Never connect a nitrogen cylinder without a regulator, never exceed the specified pressure, and never use oxygen or shop air. Wear eye protection, and release the test gas slowly before opening the system.
Tools used for this job
How do I disconnect a spring-lock A/C coupling?
Short answer: Use a disconnect tool sized for the fitting to open the garter spring inside the coupling, then separate the lines; replace the O-rings and spring if damaged before reconnecting.
Spring-lock couplings join some A/C and fuel lines without threads. A garter spring inside the female fitting snaps over a flared end on the male line. To separate them, a tool of the correct diameter slides into the coupling and expands the spring so the lines pull apart.
Recover the refrigerant before opening any A/C line. Clean the coupling first, so dirt does not enter the system. Choose the right size tool, push it into the coupling to release the spring, and pull the lines apart. Scissor-style tools grip the coupling and make the job easier where access is tight.
Replace the O-rings with the correct type for the refrigerant and lubricate them with the specified oil. Check the garter spring and replace it if stretched. Wear eye protection and gloves when disconnecting lines.
Tools used for this job
How do I make a new A/C hose with a crimper?
Short answer: Cut barrier hose square to length, install fittings with the correct ferrules, and crimp with a die that matches the hose and fitting size, then pressure test the finished assembly.
Building a hose saves time when an original hose is unavailable or slow to arrive. Start with A/C barrier hose rated for the refrigerant and fittings that match the original connections. Cut the hose square with a hose cutter so the end seats fully on the fitting.
Push the fitting into the hose to the correct depth with lubricant made for the purpose, install the ferrule, and crimp using the die size that matches the hose and fitting. Follow the crimper maker's chart for size and crimp depth. Mark the hose orientation so the fittings line up when installed.
Before installing, inspect the crimp for uniformity and check the hose assembly for leaks under pressure. Use new O-rings, lubricated with the specified oil. Wear eye protection and gloves during the job.
Tools used for this job
How do I check the accuracy of my A/C machine's scale?
Short answer: Follow the machine maker's calibration check procedure using a known test weight, and have the scale serviced if it reads outside the stated tolerance.
Charging by weight is only as accurate as the scale. Over time, scales can drift or be damaged by bumps and moving the machine. A machine that undercharges or overcharges every car causes comebacks.
Most A/C machines have a calibration check in the service menu, using a known weight. Run the check on the schedule the maker recommends, and after the machine has been moved or dropped. Many makers also recommend periodic service.
Record each check in a maintenance log, along with filter and oil changes. If the scale reads outside the tolerance, follow the maker's calibration steps or contact service. Unplug the machine before opening any panels.
Tools used for this job
Can I charge an A/C system accurately without a recover-recharge machine?
Short answer: Yes, with a refrigerant scale, a manifold gauge set, a vacuum pump and a micron gauge, you can evacuate and charge by weight to the label specification.
A full RRR machine automates recovery, evacuation and charging, but the same work can be done with separate tools. After recovering refrigerant with a recovery unit, evacuate with a vacuum pump through a manifold gauge set and confirm vacuum with a micron gauge.
To charge, place the refrigerant tank on a scale, zero it, and open the valve to let refrigerant flow until the scale shows the label amount has been delivered. Some wireless scales can control a solenoid to stop charging automatically.
Account for refrigerant left in hoses. Never charge liquid into the low side with the engine running. Wear eye protection and gloves, and keep refrigerants and equipment separated by type.
Tools used for this job
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.