Air/Hydraulic Jacks and Pumps
Air-over-hydraulic bottle jacks, foot pumps and air-assisted lifting and pressing equipment, with setup, bleeding and safe use.
How does an air/hydraulic bottle jack work?
An air/hydraulic jack uses a small air motor or air piston to drive a hydraulic pump, so shop air raises the load instead of hand pumping, while the hydraulic ram still does the lifting and holds the load until released.
Read the full answer →What air pressure does an air/hydraulic jack need?
Short answer: Many air/hydraulic jacks are designed to run on typical shop air in roughly the 100 to 175 psi range, but the exact requirement varies by model, so check the jack's manual; too little pressure can prevent it from lifting its rated load.
Air/hydraulic jacks multiply air pressure through the pump ratio to create high hydraulic pressure. If supply pressure is too low, the jack may lift slowly or stall before reaching full capacity. Too high a pressure can damage the air motor or seals.
Check the maker's specified operating range and set your regulator accordingly. Use a hose and coupler that do not restrict flow excessively, since pressure drops under flow.
Keep the air supply clean and dry. Lubricate the air motor if the maker recommends it. Never exceed rated capacity, and support raised loads on rated stands.
Tools used for this job
What is an air/hydraulic foot pump used for?
Short answer: An air/hydraulic foot pump converts shop air into high hydraulic pressure to power remote rams, presses and pullers, letting you control the pump with your foot while your hands position the work.
Foot pumps are commonly paired with shop presses, bearing pullers, hydraulic cylinders and frame straightening equipment. They connect to a single-acting cylinder through a hydraulic hose and coupler.
The pump's output pressure is limited by internal relief settings. Make sure all hoses, couplers and cylinders are rated for the pump's maximum pressure.
Inspect hoses for damage and never use your hand to check for leaks, since high-pressure fluid can penetrate skin. Wear safety glasses and stay clear of the work during pressing.
Tools used for this job
How do I bleed air from an air/hydraulic jack?
Short answer: Most bottle jacks are bled by opening the release valve, pumping the ram fully several times, and checking the oil level with the ram down, following the maker's specific procedure.
Air trapped in the hydraulic system causes spongy lifting, failure to reach full height or a load that drops. Bleeding removes it.
Typically, open the release valve, pump the jack a number of times, close the valve, extend the ram, then lower it. Some jacks have a fill plug that should be opened briefly during bleeding. Procedures vary by maker.
Use only the hydraulic oil specified, not brake fluid. Never work under a load supported only by a jack, and inspect the jack for leaks.
Tools used for this job
Why won't my air/hydraulic jack lift?
Short answer: Common causes are low hydraulic oil, air in the system, an open release valve, insufficient air pressure or a worn pump or seals.
Check the simplest things first. Make sure the release valve is fully closed. Confirm air pressure and that the hose is not restricted.
With the ram fully down, check oil level and add the specified jack oil if needed. Bleed the system. If the air motor runs but the ram does not rise, the pump valves or seals may be worn.
Do not continue to use a jack that drops or leaks. Have it repaired or replaced. Always use rated stands under raised loads. Water in the air supply can also corrode the air motor, so drain your tank and use a filter on the drop that feeds the jack.
Tools used for this job
When should I use an air-assisted jack instead of a floor jack?
Short answer: Air-assisted bottle jacks are compact, high-capacity and quick for trucks, trailers and equipment, while floor jacks are easier to position under passenger cars and have lower profiles.
Bottle jacks deliver high capacity in a small footprint but have higher minimum heights and smaller saddles. Air assist speeds lifting heavy loads.
Floor jacks roll into position and often have lower profiles and larger lifting range for cars and light trucks.
Choose based on vehicle type, lift points and clearance. Use only on level ground and always support raised vehicles on rated stands. In fleet and roadside truck work, a low-profile air/hydraulic bottle jack with extension screws covers many axle heights. Check the jack's minimum and maximum height against the lift point before buying, and use a saddle or adapter recommended by the maker so the load cannot slip.
Tools used for this job
What is a two-stage air/hydraulic pump?
Short answer: A two-stage air/hydraulic pump delivers high oil volume at low pressure to quickly advance a cylinder, then switches to a high-pressure, lower-volume stage once the load is contacted.
Single-stage pumps deliver the same flow regardless of load, so moving a ram into position can be slow. A two-stage pump speeds up the approach phase and then automatically shifts to the high-pressure stage to do the work.
They are used with presses, rams, pullers and other hydraulic cylinders. The air motor drives the pump, so the operator controls it with a pedal or valve while keeping hands free.
Match the pump's maximum pressure and oil capacity to the cylinder and hoses. Every component in the circuit must be rated for the pump's output pressure.
Use a gauge to monitor pressure, inspect hoses for damage and never stand in line with a loaded ram. Wear eye protection and keep hands away from pinch points.
Tools used for this job
Can I use an air/hydraulic foot pump on a shop press?
Short answer: Many shop presses can be fitted with an air/hydraulic pump if the press cylinder, hose and couplers match the pump's pressure rating and fittings, but follow the press maker's approved options.
Air/hydraulic pumps make pressing faster and let you use both hands to position the work. Many presses come with hand pumps and offer air/hydraulic upgrades.
Check the cylinder's rated pressure, the pump's maximum pressure and the oil reservoir capacity. The reservoir must hold enough oil to fully extend the cylinder.
Install a gauge so you know how much force you are applying. Press force is easy to overshoot with powered pumps.
Use guards and shields, wear eye protection and face protection and never stand in front of a loaded part, since parts can break and fly out under pressure.
Tools used for this job
What oil should I use in an air/hydraulic jack?
Short answer: Use the hydraulic jack oil specified by the jack's maker, usually a light anti-wear hydraulic oil, and never substitute brake fluid, motor oil or ATF unless the manual allows it.
Jack seals are designed for specific fluids. Brake fluid can destroy seals, and motor oil can contain additives that cause foaming or seal swelling.
Check the oil level with the jack fully lowered and on level ground, following the manual's procedure. Overfilling can prevent full lowering or cause leaks.
If the oil looks milky or dirty, drain and refill. Bleed air from the system after topping up.
Never get under a load supported only by a jack. Use rated jack stands, and wear eye protection when servicing.
Tools used for this job
Why does my air/hydraulic jack slowly sink under load?
Short answer: A jack that sinks under load usually has a leaking release valve, worn internal seals or contaminated oil, and it should be taken out of service until it is repaired.
The release valve must seal fully to hold pressure. Dirt in the oil can prevent it from seating. Worn piston seals allow oil to bypass internally.
Try cleaning by flushing with fresh oil as the maker directs. If sinking continues, replace seals with the maker's kit or have it professionally repaired.
Never rely on a jack to hold a vehicle. Always place rated jack stands before working underneath.
Inspect jacks regularly and remove damaged ones from service. Wear eye protection.
Tools used for this job
How do I lower an air-assisted bottle jack safely?
Short answer: Lower an air-assisted bottle jack by slowly opening the release valve as the maker directs, keeping people and body parts clear and lowering the load in a controlled way onto jack stands or the ground.
Opening the release valve quickly can drop the load suddenly. Turn the valve slowly to control the lowering speed.
Before lowering, check that tools and people are clear, and that jack stands are removed only after the load is supported.
Disconnect the air line when finished so the jack cannot raise unexpectedly.
Store the jack upright with the ram retracted. Wear eye protection and gloves, and follow the maker's procedure for your specific jack. If the jack lowers unevenly or will not lower, have it inspected before using it again.
Tools used for this job
What tonnage air/hydraulic jack do I need for trucks?
Short answer: Choose a jack rated above the load it will actually lift at the lift point, not the vehicle's total weight, and pick a height range that fits under the axle or frame point you use.
A truck's axle may carry a large share of the vehicle's weight. Check the axle weight rating and select a jack with a comfortable margin.
Low-profile jacks fit under lowered axles, while taller jacks need extensions for high frames. Use only extensions approved by the maker.
Check the minimum and maximum lift heights. A jack that is too tall will not fit, and one that is too short will need unsafe blocking.
Always support the load on rated stands and chock wheels. Wear eye protection and use the jack on a solid, level surface.
Tools used for this job
How is an air/hydraulic jack different from a pneumatic air bag jack?
Short answer: An air/hydraulic jack uses air to drive a hydraulic pump and ram, while an air bag jack lifts directly with an inflatable bellows, which is faster and lower in height but has different stability and capacity characteristics.
Air/hydraulic jacks offer precise control and high capacity in a compact package. Air bag jacks lift quickly and can fit under low clearance, popular in tire shops and racing.
Bag jacks rely on air pressure to hold the load, so leaks can cause the load to lower. Hydraulic jacks have their own release valves and seals.
Both types require jack stands for any work under the vehicle.
Choose based on your lift points, capacity and speed needs, and wear eye protection.
Tools used for this job
What is an air/hydraulic transmission jack?
Short answer: An air/hydraulic transmission jack uses shop air to drive a hydraulic pump that raises a saddle holding the transmission, letting the technician lift and position heavy transmissions and transfer cases with a foot pedal or control while keeping hands free.
Transmission jacks include tilt and side adjustments to align the transmission with the engine. Air assist makes lifting smoother and faster than hand pumping.
Secure the transmission with the jack's chains or straps before lowering or moving it.
Use the jack within its rated capacity and on a level floor.
Wear eye protection and keep hands and feet away from the load. Never move the vehicle or lift while the jack supports a component. Check the hydraulic oil level and air connections before each use.
What is an air-hydraulic riveter?
Short answer: An air-hydraulic riveter uses shop air to drive a hydraulic intensifier that pulls large or structural blind rivets with high force, making it suitable for trailers, truck bodies and heavy fabrication where hand or standard air riveters lack capacity.
Standard air riveters pull small and medium blind rivets. Large-diameter and high-strength rivets need more force, which an air-hydraulic tool provides.
Nose pieces and jaws must match the rivet size.
Check hydraulic oil levels and follow the maker's bleeding procedure.
Wear eye protection, since mandrels eject, and keep hands clear of the nose. Many shops use air-hydraulic riveters for aluminum trailer and truck body repairs where dozens of large rivets must be set consistently. Empty the mandrel collector often, and store the tool upright if the maker recommends it to keep air out of the hydraulic section.
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.