Spray Guns and Paint Equipment
What is the difference between HVLP, LVLP and conventional spray guns?
Conventional guns atomize with high air cap pressure and waste more paint, HVLP guns use high air volume at low cap pressure for better transfer efficiency, and LVLP guns aim for good atomization with less air volume, suiting smaller compressors.
Read the full answer →What spray gun tip size should I use for automotive paint?
Many painters use about 1.2 to 1.4 mm for basecoat and clearcoat, 1.4 to 1.6 mm for single-stage and sealers, and 1.7 to 2.2 mm or larger for primer surfacers, but always check the paint's technical data sheet.
Read the full answer →How do I set the air pressure on an HVLP spray gun?
Short answer: Set the inlet pressure the gun maker specifies with the trigger pulled, using a gauge at the gun inlet, because pressure measured at the wall regulator is higher than what reaches the gun under flow.
HVLP guns are designed to deliver a specific air cap pressure when supplied with a specific inlet pressure. That inlet pressure varies by gun and air cap, so check the maker's specification, often printed in the manual or on the gun.
Install a gauge or air adjustment valve at the gun inlet. Pull the trigger fully so air flows, and set the regulator or valve until the gauge reads the specified inlet pressure. Pressure drops through hoses and fittings, so a wall regulator reading is not accurate for the gun.
Some makers offer air cap test kits to verify cap pressure. Too low pressure causes poor atomization and orange peel, while too high causes dry spray and overspray. Use clean, dry, oil-free air and spray with ventilation and a respirator rated for the paint.
Tools used for this job
Gravity feed, siphon feed or pressure pot: which spray gun type is best?
Short answer: Gravity feed guns are the most common in automotive refinishing because they use paint efficiently and atomize well, siphon guns suit larger volumes and older setups, and pressure pots feed large amounts of material or heavy coatings.
Gravity feed guns mount the cup on top. Paint flows down by gravity, which helps material flow at low pressures and leaves little waste in the cup. They are the standard for most collision and custom paint work.
Siphon feed guns use a cup below the gun and rely on air flow to draw paint up. They hold more paint and are easy to set down, but they can waste material and may need more air.
Pressure pots or pressure-fed systems push paint from a separate tank through a hose. They are used for large jobs, heavy primers and coatings such as undercoating or bed liners. Choose based on job size and material, and always wear a respirator and use proper ventilation.
Tools used for this job
How do I adjust a spray gun's fan pattern?
Short answer: Use the pattern knob to set the fan width, the fluid knob to set paint flow, and test on masking paper until the pattern is evenly wet with a consistent oval shape.
Most spray guns have three adjustments: air pressure at the inlet, fan pattern width and fluid flow. The fan control changes how much air goes to the air cap horns, widening or narrowing the spray.
Start with the fan fully open and fluid set per the maker or about two to three turns open. Spray a test pattern on masking paper held vertically, triggering briefly. Look for an even oval with uniform droplets and no heavy center or split ends.
Adjust fluid to suit your gun speed and the material's coverage. A narrower fan is useful for small areas and blending. Clean horn holes if the pattern is lopsided. Always spray with proper ventilation and wear a respirator, gloves and eye protection.
Tools used for this job
How far should I hold an HVLP gun from the panel?
Short answer: Many HVLP guns are designed to spray at roughly 6 to 8 inches from the surface, closer than older conventional guns, but follow the gun and paint maker's recommendation for your setup.
Gun distance affects how wet the paint lands and how much overspray drifts away. HVLP guns produce lower velocity spray, so they are usually held closer than conventional guns. A common starting point is about a hand span from the panel, but the exact distance depends on the gun, air cap and material.
Holding the gun too close lays on heavy paint that can run or sag. Holding it too far lets droplets dry before landing, causing dry spray, rough texture and poor gloss. Distance should stay consistent across the whole pass.
Keep the gun perpendicular to the surface and move your whole arm rather than flicking your wrist, which changes distance at the ends of each pass. Practice on a test panel to dial in distance, speed and overlap. Spray only with proper booth ventilation and a respirator rated for the coatings.
Tools used for this job
How much should spray gun passes overlap?
Short answer: Most painters overlap each pass by about half to three quarters of the fan width, which builds even film thickness and helps avoid stripes, though some materials have their own recommendations.
Each pass of a spray gun deposits a band of paint that is heavier in the middle and lighter at the edges. Overlapping passes evens out the film. A 50 percent overlap is a common baseline, and many basecoat systems call for 50 to 75 percent.
Too little overlap leaves stripes or tiger striping, especially with metallic and pearl colors. Too much overlap can build heavy coats and lead to runs.
Aim the center of the fan at the lower edge of the previous pass, keep speed and distance consistent and trigger at the start and end of each pass off the panel. Follow the paint maker's technical data sheet for coat counts and flash times. Wear a respirator and use proper ventilation.
Tools used for this job
How do I clean a spray gun after painting?
Short answer: Empty the cup, flush with the correct cleaning solvent or water for the paint type, spray it through until clear, then disassemble and clean the air cap, nozzle and passages with brushes, never soaking the whole gun unless the maker allows it.
Paint left in a gun dries quickly and ruins atomization. Clean the gun right after use.
Empty leftover paint into an approved waste container. Add the cleaner recommended for the paint system, such as lacquer thinner or gun wash for solvent-based paints, or water and a water-based cleaner for waterborne paints. Spray it through the gun into a waste container until it runs clear. Remove the air cap and clean it with a soft brush. Clean the fluid nozzle and cup.
Do not use wire or drill bits in air cap holes, which can enlarge them. Avoid soaking the whole gun in solvent unless the maker approves, since it can damage seals. Lubricate needle packing as directed. Clean in a ventilated area with gloves and eye protection, and dispose of waste properly.
Tools used for this job
Why is my spray gun spitting?
Short answer: Spitting usually comes from a loose or damaged fluid nozzle, worn needle packing, a clogged cup vent, low paint in the cup or air leaking into the fluid passage.
A gun that spits or sputters sends uneven bursts of paint. Air entering the fluid path is a common cause. Check that the fluid nozzle is tight and its seat is clean. A loose nozzle lets air into the paint stream.
Worn or loose needle packing can also pull air in. Tighten or replace it. Check the cup vent hole, since a clogged vent creates a vacuum that interrupts flow. Make sure there is enough paint in the cup and that the cup is not tipped too far.
Clean the gun thoroughly and inspect for damaged parts. Strain paint before pouring it into the cup. Spray only with proper ventilation and a respirator.
Tools used for this job
What causes orange peel in automotive paint?
Short answer: Orange peel comes from poor atomization or poor flow-out, often caused by low gun pressure, holding the gun too far, paint too thick, wrong reducer for the temperature or coats applied too dry.
Orange peel is a textured surface resembling an orange's skin. It forms when paint droplets do not level out before drying.
Check gun inlet pressure against the maker's spec. Low pressure produces large droplets. Holding the gun too far or moving too fast lets droplets dry before landing. Paint mixed too thick or with the wrong reducer for shop temperature flows poorly.
Adjust technique and mixing according to the paint maker's technical data sheet. Some orange peel can be sanded and polished after curing. Wear a respirator and use proper ventilation.
Tools used for this job
What causes runs and sags when spraying?
Short answer: Runs and sags come from applying too much paint at once, holding the gun too close, moving too slowly, overlapping too much, not allowing flash time or using a slow reducer in cool conditions.
Runs form when the paint film is too heavy to stay in place before it sets. Common causes are heavy coats, slow gun speed, too much fluid flow and short flash times between coats.
Temperature matters. Cold panels and slow reducers keep paint wet longer, increasing run risk. Follow the paint maker's technical data sheet for reducer selection and flash times.
Practice consistent technique. Minor runs can often be sanded and polished after curing. Always wear a respirator and spray in a ventilated area.
Tools used for this job
Why is my spray pattern heavy on one side or banana shaped?
Short answer: A lopsided or banana-shaped pattern usually means a clogged or damaged air cap horn hole or a dirty fluid nozzle; rotate the air cap to see if the pattern follows it, then clean or replace the part.
A good spray pattern is an even oval. If one end is heavier or the pattern curves, air is not flowing evenly from the horn holes on each side of the air cap, or paint is not leaving the nozzle evenly.
Test by rotating the air cap half a turn and spraying again. If the heavy side moves with the cap, the cap is the problem. If it stays in the same place, the fluid nozzle is likely dirty or damaged.
Soak the air cap in the proper cleaner and clean holes with a soft brush or the gun maker's cleaning tools, not wire or drill bits, which enlarge holes. Inspect the nozzle tip for nicks. Replace damaged parts with the maker's matched set. Clean in a ventilated area with gloves and eye protection.
Tools used for this job
Do waterborne paints need a different spray gun setup?
Short answer: Waterborne basecoats often spray well through modern HVLP or high-efficiency guns, but they usually need stainless or water-compatible fluid parts, clean dry air and more air movement to dry between coats.
Waterborne basecoats are common in refinishing because they reduce solvent emissions. Many current guns are designed for both solvent and waterborne materials, with stainless steel fluid passages that resist corrosion.
Waterborne paints dry by evaporation of water, which depends on air movement and humidity. Shops often use air dryers or venturi blowers to speed flash times. The paint maker may recommend a particular tip size and inlet pressure for their waterborne system.
Clean guns with water-based cleaners recommended by the paint maker, and do not mix solvent and waterborne waste. Use clean, dry, oil-free air. Follow the paint maker's technical data sheet and wear a respirator and gloves even with waterborne products, since clearcoats and other components may contain isocyanates.
Tools used for this job
What is a primer spray gun and why use a separate one?
Short answer: A primer gun uses a larger fluid tip, often around 1.7 to 2.5 mm, to spray thick primer surfacers; keeping a separate gun for primer prevents contamination and wear on your topcoat gun.
Primer surfacers are thicker and contain more solids than basecoat and clear. They need a larger tip and sometimes different air cap settings to flow properly.
Using a dedicated primer gun keeps abrasive primer particles away from your basecoat and clear gun, extending its life and preventing contamination. Primer guns can be less expensive, since finish quality is less critical.
Follow the primer maker's recommended tip size and pressure. Clean the gun thoroughly after use, since primer dries quickly. Spray with proper ventilation and a respirator rated for the materials.
Tools used for this job
What is a touch-up or detail spray gun used for?
Short answer: A touch-up or detail gun has a smaller cup and pattern for small repairs, door jambs, motorcycle parts and blending, giving more control and less overspray than a full-size gun.
Detail guns are scaled-down versions of full-size guns. Their small cups hold just enough paint for small jobs, and their narrow fan patterns help paint small areas without coating everything nearby.
They are useful for spot repairs, jambs, under-hood areas, small parts and custom work. Some are HVLP and require less air than full-size guns.
Use the correct tip size for the material and adjust air pressure according to the maker. Clean them carefully after each use, since small passages clog easily. Wear a respirator and use proper ventilation.
Tools used for this job
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.