Air-Operated Shop Equipment
Grease pumps, fluid pumps, shakers, testers and other shop equipment that runs on compressed air.
What does a 50:1 ratio mean on an air-operated grease pump?
The ratio means the pump multiplies inlet air pressure about 50 times at the grease outlet, so 100 psi of shop air can theoretically produce around 5,000 psi of grease pressure before losses.
Read the full answer →How do I set up an air-operated grease pump on a drum?
Short answer: Mount the pump in the drum with its follower plate, connect a filtered and regulated air supply, attach a rated grease hose and control valve, then prime the pump until grease flows without air.
Drum and pail grease systems usually include a pump tube, a follower plate that rides on the grease surface and a cover. The follower keeps grease feeding to the pump inlet and helps prevent air pockets that cause the pump to run away or deliver spurts.
Supply air through a filter and regulator. Start with low air pressure and raise it only as needed for the fittings you service. Many shops use a hose reel to keep the grease hose off the floor.
Prime by operating the control valve into a container until grease flows steadily. Check all connections for leaks, and tighten fittings with the system depressurized.
Release air and grease pressure before changing drums or servicing the pump. Wear eye protection and gloves, and follow the maker's instructions for the specific pump.
Tools used for this job
What is a pneumatic oil pump used for in a shop?
Short answer: A pneumatic oil pump moves motor oil, gear oil or ATF from a drum to a dispense valve using shop air, which speeds up oil changes and helps track fluid use compared with pouring from containers.
Low-ratio pumps, often 3:1 or 5:1, deliver good volume of thin fluids. They mount in a drum or bulk tank and feed a hose and metered or unmetered dispense valve.
Shops use them in lube bays to deliver oil to the vehicle without carrying jugs. Some systems use overhead reels and fluid management meters to record quantities.
Use a clean filtered and regulated air supply. Keep fluids separated with dedicated pumps and hoses to avoid cross-contamination.
Depressurize before maintenance, wipe up drips quickly and wear eye protection. Check that hoses and valves are rated for the pump's outlet pressure.
Tools used for this job
How does an air-operated paint shaker work?
Short answer: An air-operated paint shaker uses an air motor to vibrate or oscillate a clamped can, mixing pigments and metallic flakes without electricity, which suits shops that want to avoid electrical equipment near paint.
The can is clamped in a holder and the air motor drives a rapid shaking motion. Shaking time depends on the paint type and how long it has been sitting.
Air operation keeps electric motors out of the mixing area, which is one reason some paint rooms prefer it. It still needs a clean air supply, ideally with a filter and regulator.
Make sure the can lid is sealed and clamped securely before starting. Follow the paint maker's mixing instructions; some products must be stirred instead of shaken.
Keep solvent vapors away from ignition sources, wear eye protection and use a respirator suitable for paint when open containers are present.
Tools used for this job
Can an EVAP smoke machine use shop air?
Short answer: Some EVAP smoke machines connect to shop air or nitrogen to push smoke into the system, while others have an internal pump; check the machine's instructions, because EVAP testing typically requires very low pressure.
Smoke machines produce a visible vapor and push it into the EVAP system, intake or exhaust to reveal leaks. Machines that use shop air include a regulator that reduces pressure to a safe level for EVAP components.
Too much pressure can damage EVAP valves and seals. Use only the machine's regulated output.
Some manufacturers recommend inert gas for fuel system testing because fuel vapors are present. Follow the maker's guidance on whether shop air is acceptable.
Work in a ventilated area away from ignition sources and wear eye protection.
Tools used for this job
What is a pressure testing regulator kit used for?
Short answer: A pressure testing regulator kit reduces shop air or nitrogen to a controlled low pressure with an accurate gauge, so you can pressurize a system for leak testing without exceeding its rated pressure.
Many automotive systems, such as cooling, intake and A/C, must be tested well below shop air pressure. A dedicated regulator kit lets you set and hold a precise test pressure.
Some kits are designed for nitrogen and A/C use, while others work with shop air for intake and boost leak tests. Use the right gas for the system; A/C systems are usually tested with dry nitrogen.
Increase pressure gradually and never exceed the vehicle maker's test pressure. Watch the gauge for drops that indicate leaks.
Release pressure slowly before disconnecting, and wear eye protection.
Tools used for this job
What is an air motor?
Short answer: An air motor converts compressed air into rotation, usually with vanes or pistons, and powers air tools, mixers, pumps and winches where electric motors would be less suitable.
Vane air motors are the most common type in handheld tools. Piston motors provide higher torque at low speed and are used on hoists and larger equipment.
Air motors can stall without overheating, start and stop frequently and work in wet or explosive environments when rated for it. Speed and torque are controlled by adjusting air pressure and flow.
They are less energy efficient than electric motors, so they use more compressor capacity.
Air motors need clean, lubricated air unless rated oil-free. Wear eye protection and keep guards in place on equipment they drive.
What is an air-operated diaphragm pump?
Short answer: An air-operated double diaphragm pump uses compressed air to flex two diaphragms that move fluid, handling thick, abrasive or chemical fluids and running dry or stalling without damage.
Shops use diaphragm pumps to transfer waste oil, coolant, solvents and other fluids. Because they have no electric motor, they are popular where flammable liquids are handled, though the pump and accessories must be grounded and rated for the fluid.
Flow rate depends on air pressure and the fluid. Pumps can stall against a closed valve and restart when the valve opens.
Choose diaphragm and seal materials compatible with the fluid. Use a filter-regulator on the air supply.
Wear eye protection and chemical-resistant gloves, and depressurize the pump before maintenance.
What air supply does a tire changer need?
Short answer: Most shop tire changers need a regulated air supply around their specified pressure, a filter and lubricator in many cases, and enough flow for the bead breaker and clamps, so check the machine's manual.
Tire changers use air cylinders for bead breaking, clamping and sometimes inflation. The maker lists the required pressure range and air connection.
Many machines include a built-in filter, regulator and lubricator. Keep the lubricator filled with the specified oil and drain water regularly.
Low pressure makes the bead breaker weak and clamps slip. Excess pressure can damage parts and is a safety hazard.
Use proper inflation procedures and an inflation cage where required, and wear eye protection. A dedicated air drop with a shutoff valve near the machine makes service easier.
How do air-operated lift safety locks work?
Short answer: Many two-post and four-post lifts use small air cylinders to release the mechanical safety locks when lowering, so the operator presses a button or lever that sends shop air to pull the locks clear while the lift descends.
The mechanical locks engage automatically as the lift rises, catching the carriage at intervals so the load rests on steel rather than hydraulic pressure. To lower the lift, the locks must be pulled out of the way.
On air-release lifts, a valve sends shop air to small cylinders on each column. If air pressure is too low or a line leaks, one side may not release, causing the lift to hang on one lock or lower unevenly.
Supply clean, dry, regulated air at the pressure the lift maker specifies. Drain water from the filter regularly, and inspect air lines along the columns for chafing.
Always lower the lift onto its locks before working under a vehicle, keep people clear while lowering and follow the lift maker's daily inspection checklist. Wear eye protection when servicing the lift's air components.
What is an air-operated lube reel system?
Short answer: An air-operated lube reel system combines bulk fluid pumps, overhead or wall-mounted hose reels and dispense valves, letting technicians pull oil, grease or ATF hoses to the vehicle and dispense from pressurized bulk containers.
Lube bays use reels to keep hoses organized and off the floor. Each reel is connected to a pump on a drum or bulk tank.
Air reels may also be included for tire inflation and air tools.
Pumps and hoses must be matched to fluid type and pressure. Use separate lines for each fluid to avoid contamination.
Relieve pressure before servicing, wipe up spills promptly and wear eye protection and gloves. Meters at the dispense valves help track fluid use for each repair order.
Tools used for this job
What is an air-evacuated oil drain?
Short answer: An air-evacuated oil drain is a wheeled drain tank that you empty by connecting shop air to pressurize the tank, which pushes the used oil out through a hose into a bulk waste oil tank without tipping or pouring.
Oil drains collect oil from vehicles on lifts. Emptying them by pouring is messy and heavy.
Air-evacuated drains use regulated low pressure to push oil out. The tank must be rated for that pressure and have a safety valve.
Follow the maker's pressure limits and open the evacuation valve before applying air.
Wear eye protection and gloves, and keep waste oil away from ignition sources. Check the tank's gauge, safety valve and hoses regularly, and never exceed the pressure printed on the tank. Release all pressure before opening the drain funnel or moving the unit. Keep the drain's hose end secured in the bulk tank so it cannot whip out while pressurized.
Tools used for this job
What is a pneumatic air hoist?
Short answer: A pneumatic hoist uses an air motor to lift and lower loads with chain or wire rope, offering smooth variable speed, continuous duty without motor burnout and suitability for wet or hazardous areas, but it must be rated and inspected like any hoist.
Air hoists are found in engine rebuild shops, fabrication shops and industrial plants. Because the air motor can stall without overheating, they handle frequent starts and long lifts well, and pendant controls give fine speed control for positioning heavy parts.
They need a steady supply of clean, lubricated air at the volume the maker specifies. A starved hoist lifts slowly, and a dirty supply wears the motor and brake.
Hoists must be mounted to a beam, trolley or crane rated for the load, and the hoist's own capacity must not be exceeded. Hooks, chain, brakes and limit devices require regular inspection according to the maker and workplace rules.
Never stand or work under a suspended load, use proper rigging and slings and wear eye protection, gloves and a hard hat where overhead lifting takes place.
What is an air-powered drum vacuum?
Short answer: An air-powered drum vacuum uses a venturi head mounted on a steel drum to suck up liquids, sludge and debris with shop air, making it useful for cleaning up coolant, oil and water spills or emptying pits without an electric motor.
The venturi generator creates suction using compressed air. Many models can also reverse to pump the drum's contents out.
Use a drum and lid designed for the vacuum head and follow the maker's pressure limits.
Do not use it to collect flammable liquids unless the maker specifically approves it and the drum is grounded.
Wear eye protection and hearing protection, and dispose of collected fluids properly. Drum vacuums use a fair amount of air, so check your compressor's capacity before relying on one for large cleanups. Keep the drum's level well below the shutoff float so liquid is not drawn into the venturi.
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.