Die Grinders
Straight, angle and pencil die grinders: collets, burrs, discs, speed ratings and safe use.
Can I use a flexible shaft with an air die grinder?
Short answer: Flexible shaft attachments are rare for air die grinders, so when you need extra reach, an extended die grinder or a long-shank accessory rated for the tool's speed is the usual solution.
Flexible shafts are common on electric rotary tools to keep the heavy motor away from your hand. Air die grinders are already light, so makers generally offer extended-body models instead.
An extended grinder places the collet several inches beyond the body, reaching into intake ports, frame rails and deep cavities. Long-shank burrs add reach too, but they lower the safe speed and can whip if run too fast.
Check the accessory maker's speed limits for long shanks, keep overhang as short as possible and use moderate pressure. Hold extended tools with both hands for control, and wear eye protection and a face shield.
Tools used for this job
How do I dress a mounted grinding stone?
Short answer: Use a dressing stick or diamond dresser against the spinning stone at light pressure to remove glazing and loaded metal and to true its shape, while staying within the stone's speed rating.
Mounted points and stones glaze over with use, especially on soft metals, and they wear out of round. A glazed stone rubs instead of cutting and heats the work.
With the grinder running at a moderate speed and the shank firmly clamped, hold the dressing stick against the stone and move it across the face. Rest your hands on a solid support so the dresser does not catch. Stop once fresh, sharp grit is exposed and the stone runs true.
Inspect the stone for cracks before and after dressing, and discard any that are cracked or worn down to the shank. Wear safety glasses, a face shield and a dust mask, since dressing creates abrasive dust.
What are cartridge rolls and spiral bands for die grinders?
Short answer: Cartridge rolls and spiral bands are abrasive tubes that mount on mandrels, used to blend, deburr and smooth inside holes, ports and curved surfaces where flat discs cannot reach.
Cartridge rolls are tightly wound abrasive cloth on a core, either straight or tapered. Spiral bands slip over a rubber drum mandrel that expands slightly as it spins to hold the band.
They are popular for cylinder head port work, smoothing inside tubes, cleaning up holes and blending welds in curved areas. Grits range from coarse for shaping to fine for finishing.
Use the correct mandrel for each type, keep the roll fully supported and check the speed rating, which is often lower than the grinder's free speed for larger diameters. Wear a dust mask and eye protection, and clean abrasive grit from engine parts thoroughly before assembly.
Tools used for this job
Why do carbide burrs chip or break?
Short answer: Carbide burrs usually chip or break from heavy pressure, side loading, excessive overhang, dropping them, or running the wrong speed or cut type for the material.
Tungsten carbide is very hard but brittle. Pushing hard on the burr, prying with it or letting it catch in a narrow slot can snap off flutes or the whole head.
Long shanks with lots of overhang flex and break more easily. Running too slow can cause the burr to grab, while running too fast for its size can overheat it. Cutting material it is not designed for, such as hardened steel with a burr meant for aluminum, also chips flutes.
Use light pressure, keep the burr moving, insert the shank fully and choose the right burr cut for the job. Store burrs so they do not knock together. Always wear eye protection and a face shield, because carbide chips can fly at high speed.
Tools used for this job
Can I grind out spot welds with a die grinder?
Short answer: Yes, a small burr or abrasive point can grind through the top layer of a spot weld so the panels separate, which is useful where a spot weld drill cannot reach, though it is slower and leaves a larger mark.
Collision procedures usually call for a spot weld cutter in a drill, which removes the weld cleanly from the outer panel. In tight corners, curved flanges or where the cutter will not fit, a die grinder with a small ball or cylinder burr lets you grind just through the top sheet.
Work slowly and stop when the outer panel lets go, so you do not thin the flange that stays on the vehicle. A panel separator chisel finishes the job once the welds are relieved.
Follow the vehicle maker's repair procedure for the area, especially around high-strength steel. Shield interior parts and wiring from sparks, and wear a face shield over safety glasses, gloves and hearing protection.
Tools used for this job
Can I engrave or mark metal parts with a die grinder?
Short answer: A die grinder with a small pointed carbide burr or diamond point can engrave identification marks and simple lines on metal, but it is harder to control than an engraving pen, so practice on scrap first.
Shops sometimes mark tools, parts or fixtures with an ID or a line for alignment. A pencil or mini die grinder with a fine cone or point burr cuts shallow lines in steel and aluminum.
Hold the grinder like a pen, rest your hand on the work for support, and use light pressure at moderate speed. Deep cuts can weaken thin parts, so keep marks shallow and away from stressed areas such as edges of brackets and suspension parts.
Do not engrave on safety-critical components like wheels, steering parts or lifting equipment. Use paint markers or tags there instead. Wear eye protection and secure small parts in a vise rather than holding them by hand.
Tools used for this job
Can I clean carbon from combustion chambers with a die grinder?
Short answer: Carbon can be removed with a soft nonwoven pad or a brass brush in a die grinder at low speed, but avoid abrasives that cut metal, and keep valve seats, gasket surfaces and cylinder walls protected.
When a cylinder head is off, heavy carbon in the combustion chambers and on piston tops is sometimes cleaned up. Aggressive burrs and coarse discs remove metal, change chamber volume and damage valve seats, so they are the wrong choice for cleaning.
Use a soft brass or nylon brush, or a fine nonwoven pad, at low speed and light pressure. Plug or cover oil and coolant passages and keep debris out of the cylinders. Some engine builders prefer chemical cleaners or blasting at a machine shop instead.
Check the engine maker's guidance on abrasive use near sealing surfaces, since debris can damage bearings. Wear eye protection and a dust mask, and clean all parts thoroughly before reassembly.
Tools used for this job
How do I keep metal chips out of an engine when using a die grinder?
Short answer: Seal every opening with tape, plugs or clean rags, use a vacuum to collect chips as you go, and clean the area and parts thoroughly before reassembly.
Grinding chips and abrasive grit in an engine can scratch bearings, cylinder walls and oil pump parts. Engines and transmissions have many passages where debris can hide.
Before grinding on or near an engine, stuff clean rags into intake ports and open passages, tape over oil and coolant holes, and cover open crankcases. Position a shop vacuum nozzle near the work to catch chips. Grind with the part removed from the engine whenever practical.
Afterward, remove the coverings carefully so trapped debris does not fall in, then wash parts with solvent and blow them out with low-pressure air while wearing safety glasses. Inspect passages with a light before assembly.
Tools used for this job
Why is my die grinder blowing oil onto the work?
Short answer: Oil on the work usually comes from overoiling the tool or an inline lubricator set too high, and it can be reduced by running off excess oil into a rag and choosing a rear exhaust grinder.
Air tool oil travels through the motor and leaves with the exhaust. A few drops is enough. Too much causes oil spray that contaminates welds, paint prep areas and engine parts being cleaned.
After oiling, run the grinder briefly while pointing the exhaust into a shop towel. If you use an inline lubricator, set it to a light drip or move it off lines used for grinding. Many die grinders have rear exhaust or exhaust hoses that direct air away from the work.
Clean any oily surface before welding or painting, since oil causes porosity and fisheyes. Wear safety glasses, because oil mist can blow back toward your face.
Tools used for this job
Can I slow down an air die grinder with a regulator?
Short answer: Lowering inlet pressure with a regulator reduces a die grinder's speed and power together, which can help with delicate work, but the tool will stall more easily and speed control is not precise.
An inline regulator at the tool lowers pressure, so the motor turns slower and with less torque. For small burrs on soft material or polishing, that can improve control.
The throttle lever also controls speed. Some die grinders have a built-in speed control knob. The drawback of reducing pressure is that the grinder bogs down under load, which can cause chatter.
For work that needs low speed with good torque, choose a lower-speed grinder model. Never use a regulator to make an accessory safe if its rated speed is below the tool's free speed, since speed rises when the load drops. Wear eye protection.
Tools used for this job
Can I sharpen mower blades or chisels with a die grinder?
Short answer: A die grinder with a grinding stone or flap wheel can sharpen mower blades and chisels, but a bench grinder or file gives a more even edge, and you must avoid overheating the steel.
A die grinder is handy for touching up edges on equipment you cannot easily remove. Use a mounted stone or flap wheel and follow the original edge angle.
Overheating can ruin the temper of hardened steel. Grind in short passes and let the part cool. Do not quench a hot chisel in water if the maker advises against it.
For mower blades, remove the blade and balance it after sharpening. Wear eye protection, gloves and a face shield, and secure the part in a vise.
Tools used for this job
How do I grind a weld flush on a body panel without warping it?
Short answer: Use a flap wheel or fine abrasive disc on an angle die grinder, grind in short passes and move around the panel, letting each area cool, so heat does not distort thin sheet metal.
Body panels are thin and expand quickly with heat. Long grinding in one spot can warp them.
Grind just enough to knock the weld down, then move to another weld on a different part of the panel. Come back once the first area has cooled enough that you can hold your hand near it comfortably. Compressed air or a damp cloth near, not on, the area can speed cooling, but avoid quenching hot metal with water.
Keep the disc nearly flat and use light pressure. Heavy pressure builds heat and gouges the panel. Switch to a finer grit to finish, and stop before you thin the surrounding metal, which weakens the repair and makes it more prone to warping.
Stitch welding in short, spaced tacks also reduces heat before you ever start grinding. Wear eye protection, gloves and a dust mask, and keep sparks away from glass and upholstery.
Tools used for this job
Can I deburr sheet metal edges with a die grinder?
Short answer: Yes, a flap wheel, abrasive point or deburring burr in a die grinder removes sharp burrs from cut sheet metal edges quickly, but use light passes so you do not thin or round the edge more than needed.
Cutting sheet metal with shears, nibblers or cut-off wheels leaves sharp burrs that can cut hands and wiring and keep panels from fitting. A small flap wheel or a fine cone burr run along the edge at a shallow angle cleans them up fast.
Clamp or support the panel so it does not vibrate, and work the full length in one steady pass instead of grinding one spot. For long straight edges, a hand file or deburring tool may give a straighter result.
Deburr both sides if the edge will touch wiring, hoses or weatherstrip. Bare edges rust quickly, so prime them soon after. Wear cut-resistant gloves, eye protection and hearing protection.
Tools used for this job
Can a die grinder work on hardened steel?
Short answer: Carbide burrs can cut some hardened steels slowly, but very hard parts are usually better ground with an abrasive stone or a CBN or diamond point, using light pressure to avoid chipping and overheating.
Hardened parts like broken taps, drill bits, bearing races and tool steel resist most cutting tools. Carbide burrs can work on moderately hard steel, but they wear and chip quickly on fully hardened parts.
Aluminum oxide and silicon carbide mounted points grind hard steel more reliably, and CBN or diamond points last longer on very hard material. Run at the accessory's rated speed, keep pressure light and grind in short passes.
Heat can change the hardness of the part and crack it, so let it cool between passes. Hard material often produces small sharp chips and abrasive dust. Wear safety glasses, a face shield and a dust mask.
Tools used for this job
How do I cut a slot in a stripped screw head with a die grinder?
Short answer: Use a small cut-off wheel or thin burr to cut a straight slot across the screw head, then turn it out with a flat screwdriver or impact driver bit.
Phillips and hex screws with stripped recesses are common on brake rotors, door hinges and trim. Cutting a new slot gives a flat blade something to grip.
Choose a small wheel rated above the grinder's speed. Cut across the center of the head, deep enough for the screwdriver to seat but not so deep that the head breaks. Avoid grinding into the surrounding part.
A hand impact driver with a flat bit works well to break the screw loose. Penetrating oil and heat can help. Wear a face shield, since small wheels can shatter, and protect nearby surfaces from sparks.
Tools used for this job
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.