Heavy-Duty and Fleet Air Tools
Air tools and air supply for trucks, buses, farm and fleet service work.
What air tools does a fleet shop use for truck wheel service?
Fleet shops typically use 1-inch or 3/4-inch drive impact wrenches with extended anvils for lug nuts, along with torque wrenches or torque multipliers for final tightening, high-flow air supply and wheel dollies or lifts for handling.
Read the full answer →Should I use a 3/4-inch or 1-inch impact for truck lug nuts?
Short answer: A 1-inch impact is the common choice for heavy truck lug nuts, while a strong 3/4-inch impact can handle medium-duty trucks and lighter loosening jobs; check the tool's torque ratings against the work.
Truck lug nuts are often tightened to several hundred foot-pounds, and corrosion raises breakaway torque. A 1-inch impact provides reserve power and uses larger sockets designed for the job.
Some modern 3/4-inch impacts deliver high torque in a lighter package, making them easier to handle. They suit medium-duty trucks, farm equipment and general heavy work.
Extended anvils help reach recessed nuts, but they reduce delivered torque slightly.
Choose impact-rated sockets sized for the drive. Wear eye protection and hearing protection, and support heavy tools to avoid strain.
Tools used for this job
Why do heavy-duty impacts need 1/2-inch air hose?
Short answer: Large 3/4-inch and 1-inch impacts use much more air than small tools, and a 1/2-inch hose with high-flow fittings reduces pressure drop so the tool can deliver its rated power.
Air flow drops sharply through narrow hoses over long runs. A heavy impact starved of air hits weakly, making stubborn nuts harder to remove.
Makers often specify hose size and inlet size. Many 1-inch impacts have a 1/2-inch NPT inlet.
Use short leader hoses or whips, minimize adapters and keep couplers in good condition.
Heavier hose is harder to handle, so use reels and secure connections. Wear eye protection and use whip checks on large hoses where required. A gauge at the tool inlet while it runs shows whether the supply is adequate.
Tools used for this job
What is a pneumatic torque multiplier?
Short answer: A pneumatic torque multiplier uses an air motor and a gearbox to deliver high, controlled torque smoothly, often with a reaction arm, and can tighten to a set value more accurately than an impact wrench.
Torque multipliers are used for large fasteners on trucks, heavy equipment and industrial machinery. Unlike impacts, they apply continuous torque, and many models can be calibrated.
Output is set by adjusting air pressure with a regulator, using a chart from the maker.
The reaction arm must bear against a solid surface. Keep hands away from the reaction arm, since it can pinch with great force.
Follow the maker's instructions and wear eye protection and gloves. Have the tool's calibration checked on the schedule your shop or the maker recommends.
How do I loosen inner and outer dual wheel nuts on older trucks?
Short answer: Older stud-piloted dual wheels use inner and outer cap nuts with different threads on each side of the truck, so you must identify the thread direction and nut type before applying an impact.
Some older wheel systems use left-hand threads on one side of the vehicle. Applying the impact in the wrong direction tightens the nut and can damage studs.
Check for markings on studs or nuts, and consult the vehicle's service information.
Use the correct socket for each nut type and follow the maker's sequence for loosening and tightening.
Support wheels before removal, wear eye protection and gloves and follow your shop's wheel service procedures. Inspect studs and cap nuts for damaged threads and replace any that are worn before reinstalling the wheels.
Tools used for this job
What air tools help with slack adjuster service on trucks?
Short answer: Slack adjuster service on trucks often uses an air ratchet or impact for mounting bolts, an air hammer to free seized clevis pins and camshafts, and a grease gun for the adjuster's fitting, while final adjustment is done by hand and checked to the maker's stroke limits.
Automatic slack adjusters need periodic lubrication and inspection. Seized clevis pins and splines are common, and an air hammer with a blunt punch helps free them.
Use a grease gun on the adjuster's fitting as the maker directs.
Never manually back off an automatic adjuster repeatedly to fix stroke, since that hides a brake problem.
Chock wheels, cage spring brakes when required and wear eye protection and gloves. Measure pushrod stroke with the brakes applied at the specified air pressure, and replace adjusters that do not keep stroke within limits. Follow the vehicle maker's and regulatory inspection procedures.
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.