Store relaunching soon · pro diagnostics & tools for independent shopsjoseph@directtoolsource.com
Direct Tool SourcePro Diagnostics
Home / Answers / Air Tools & Compressed Air / Spray Guns and Paint Equipment

Spray Guns and Paint Equipment

51 answers · last reviewed 2026-11-20

Why does metallic paint look striped or mottled?

Short answer: Striping and mottling in metallic paint come from uneven gun distance, speed or overlap, incorrect pressure, too-wet coats or wrong reducer speed, which cause metallic flakes to settle unevenly; a final control coat often evens them out.

Metallic and pearl flakes orient as the paint dries. Wet areas let flakes sink and appear darker.

Keep gun distance and speed consistent, and use proper overlap.

Follow the paint maker's recommendations for pressure and drop or control coats.

Wear a respirator and eye protection while painting. Hold the gun perpendicular and avoid arcing your wrist at the ends of each pass, which changes distance and leaves stripes. A gun with an uneven fan pattern also causes striping, so test the pattern on paper first and clean or replace a damaged air cap. Good lighting in the booth helps you see mottling while you can still correct it with the next coat, before applying clear.

What is flash time between coats when spraying paint?

Short answer: Flash time is the waiting period between coats that lets solvents evaporate so the next coat can be applied without runs, solvent pop or trapped solvents, and it varies with the product, film thickness, temperature and airflow, so follow the paint maker's technical data sheet.

Each coat of primer, base or clear contains solvents or water that must partly evaporate before the next coat goes on. Applying too soon traps solvents underneath, which can cause runs, dieback, poor gloss or tiny bubbles called solvent pop.

Waiting too long can be a problem too. Some products have a recoat window, and exceeding it may require scuffing before the next coat for proper adhesion.

Temperature and humidity change flash times. Cold, still air slows evaporation, while warm air with good movement speeds it. Basecoats often look dull or matte when ready for the next coat.

Check the technical data sheet for each product, use the right reducer for the temperature, ventilate well and wear a properly fitted respirator, eye protection and gloves while spraying.

What causes solvent pop in automotive paint?

Short answer: Solvent pop appears as small blisters or pinholes in the finish when solvents trapped under a skinned-over surface escape, usually from coats that are too heavy, too little flash time, the wrong reducer for the temperature or forcing the cure with heat too early.

As a coat dries, the surface can skin over while solvent is still escaping from below. When that solvent finally breaks through, it leaves tiny craters or bubbles.

Heavy wet coats, short flash times between coats and fast reducers in hot conditions are common causes. Baking or using infrared heat too soon after spraying can also trap solvents.

Prevention starts with following the product's recommended film thickness, flash times and reducer selection. Medium wet coats usually work better than one heavy coat.

Minor pop may be sanded and refinished after full cure, while severe cases need the coating removed. Always ventilate well and wear a properly fitted respirator, gloves and eye protection when spraying and sanding.

How do I avoid dust nibs when spraying paint?

Short answer: Avoid dust nibs by cleaning the work area, wetting the floor if appropriate, using filtered air, blowing off and tack-ragging the panel just before spraying, wearing a lint-free paint suit and keeping the spray area closed to drafts.

Dust nibs are particles that land in wet paint and leave small bumps. They come from the air, the vehicle, the painter and the air supply.

Clean the booth or garage thoroughly the day before so dust settles. Many home painters lightly wet the floor to hold dust down, while professional booths rely on filtered airflow.

Blow off seams and gaps, then wipe with a tack cloth immediately before painting. A lint-free suit and hood keep fibers from clothing out of the finish.

Use a filter at the gun to stop particles in the air line. Minor nibs can be removed by wet sanding and polishing after cure. Ventilate well and always wear a properly fitted respirator.

Tools used for this job

DeVilbiss 803643 80 CFM Air Filter Cleaner with Regulator HAR680

How do I spray paint in cold or humid weather?

Short answer: In cold or humid weather, use the paint maker's slower or faster reducer as directed, warm the panels and materials to the recommended temperature, extend flash times and avoid spraying when surfaces are near the dew point, since moisture can cause blushing and poor adhesion.

Most automotive coatings have a minimum application temperature, often around 60 to 65 degrees Fahrenheit. Below that, flash and cure slow dramatically and runs become more likely.

Humidity can cause blushing, a milky haze caused by moisture condensing in the evaporating film. Make sure surfaces are warmer than the dew point.

Store paint and the vehicle inside to warm up before spraying. A dryer in the air system matters more in humid weather because compressors produce more water.

Never use open-flame heaters in a spray area, since paint vapors are flammable, and always wear a properly fitted respirator and eye protection.

Tools used for this job

DeVilbiss 130500 Desiccant Air Dryer System CT-30

How do I paint wheels with a spray gun?

Short answer: Paint wheels with a spray gun by stripping or scuffing them, cleaning thoroughly, masking the tire or removing it, mounting the wheel so you can reach all sides, and applying light coats from several angles to reach the spokes and barrel without runs.

Wheels have deep pockets and edges that are easy to miss or overload. Hanging the wheel or placing it on a rotating stand helps reach every surface.

Prepare by removing old flaking paint, then use a primer suited to aluminum or steel.

A smaller tip or detail gun helps control the spray in tight spokes. Spray the inner barrel and back first, then the face.

Allow full cure before mounting tires and torquing lug nuts. Ventilate well and wear a properly fitted respirator, gloves and eye protection.

Tools used for this job

Anest Iwata 9235 High Transfer Efficiency Spray Gun with Cup AZ3HTE2-15G

General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.