Tire Shop Air Equipment
Air supply for tire changers, balancers, nitrogen and inflation in tire service.
What is a nitrogen tire inflation generator?
A nitrogen generator uses shop compressed air and a membrane or pressure-swing system to separate nitrogen from oxygen, then stores higher-purity nitrogen in a tank for filling tires through inflation hoses or cabinets.
Read the full answer →Is nitrogen better than air for car tires?
Short answer: Nitrogen can lose pressure a little more slowly and carries less moisture than typical shop air, but regular pressure checks matter far more for most drivers than the gas used, and air is fine for everyday tires.
Nitrogen molecules pass through tire rubber somewhat more slowly than oxygen, and generator nitrogen is dry. Supporters point to steadier pressure and less internal corrosion. Racing, aviation and some fleets use nitrogen for consistency.
For daily drivers, the practical benefit is modest. Tires filled with air still hold pressure well if they are checked monthly and topped off.
Mixing air into nitrogen-filled tires is safe. It simply lowers the nitrogen concentration.
Whatever the fill gas, inflate to the vehicle's placard pressure, check tires when cold and wear eye protection when inflating.
Tools used for this job
Why is my tire changer bead breaker weak?
Short answer: A weak bead breaker is usually caused by low supply pressure, a leaking cylinder seal, a worn control valve or an air restriction such as a clogged filter, kinked line or undersized coupler.
Bead breakers use a large air cylinder to apply force. Pressure at the machine below the maker's recommended range reduces force directly.
Check the machine's gauge while operating the bead breaker. If pressure drops sharply, the supply hose, coupler or compressor may be inadequate.
Listen for air leaks at the cylinder and valve. Rebuild kits are available for many machines.
Lock out air before servicing, follow the maker's instructions and wear eye protection. Also inspect the bead breaker blade and pivot for wear or binding that wastes force.
How do I maintain the lubricator on a tire changer?
Short answer: Keep the tire changer lubricator filled with the oil the maker specifies, set the drip rate according to the manual, drain the filter bowl regularly and check that oil is reaching the valves and cylinders.
Many tire changers have built-in filter, regulator and lubricator units. The oiler supplies a small amount of oil to valves and cylinders for smooth operation.
Using the wrong oil can damage seals. Use the type the maker lists.
Drain water from the filter daily and clean the bowl when needed.
Release air pressure before refilling or servicing, and wear eye protection. If the machine's movements become slow or jerky, an empty lubricator or a water-logged filter is a common cause. Some newer machines are designed to run without added oil, so follow the specific manual rather than assuming every changer needs a lubricator. Keep a log of refills if several technicians share the machine.
Tools used for this job
What is a valve core removal inflation tool?
Short answer: A valve core removal inflation tool lets you unscrew and hold the valve core while connected to the valve, allowing much faster inflation or deflation through the open stem, then reinstall the core without losing pressure.
These tools are used with large tires and when seating beads, where the core restricts flow.
The tool attaches to the valve stem, removes the core into a chamber and then lets air flow.
After inflation, the core is reinstalled before removing the tool.
Use an inflation cage where required and wear eye protection. Never exceed the tire's bead-seating pressure limit. Inspect the tool's seals and chuck regularly, since a worn seal leaks and slows inflation. Keep track of removed cores so none are lost inside the tool or dropped, and replace cores that look damaged. Check final pressure with an accurate gauge after the core is reinstalled.
Can compressed air damage TPMS sensors?
Short answer: Clean, dry air will not harm TPMS sensors, but water, oil and debris from a poorly maintained air system can corrode valve stems and sensor parts or clog the sensor port, so tire inflation air should be filtered and dry.
TPMS sensors mount inside the wheel, usually attached to the valve stem. Moisture from shop air can collect in the tire and contribute to corrosion of aluminum stems, nickel-plated cores and wheel surfaces. Oil can coat the sensor and attract dirt.
Drain compressor tanks daily, keep water separators and filters serviced and supply tire stations from a branch without an inline oiler. Many tire shops also use nitrogen or dried air.
When servicing TPMS valves, use the correct cores and torque the stem nut to the sensor maker's specification, since overtightening can crack sensors.
Inspect stems for corrosion when tires are off, and replace service kits as recommended. Wear eye protection when inflating tires.
Tools used for this job
What air supply does a wheel balancer need?
Short answer: Many wheel balancers run on electricity alone, while some models use shop air for pneumatic wheel clamping or lifts, so check the balancer's manual for required pressure, connection and filtration.
Pneumatic clamping speeds up mounting wheels and reduces errors from hand-tightened wing nuts. Balancers with wheel lifts may use air cylinders.
Supply clean, regulated air at the maker's specified pressure.
Low air pressure can let wheels slip during spin, giving incorrect readings.
Keep hands clear while clamping and spinning, and wear eye protection. If clamping feels weak or slow, check the regulator setting at the machine, drain its filter and listen for leaks at the clamp cylinder. Run the air line to the balancer with a shutoff valve so it can be serviced without affecting other equipment. Follow the balancer maker's calibration routine after any repair that affects clamping.
What air tools are needed for tire plug and patch repairs?
Short answer: Tire plug-patch repairs commonly use a low-speed air drill or reamer to clean the injury, an air tire buffer to prepare the inner liner, an inflator with an accurate gauge and a bead breaker or tire changer to dismount the tire for an inside repair.
Industry guidelines call for repairs from the inside with a combination plug-patch for passenger tires, after dismounting and inspecting the tire.
A low-speed buffer prepares the liner without overheating rubber.
The injury must be within the repairable tread area and size limits.
Follow tire industry repair standards, inflate in a cage or with a clip-on chuck while standing aside and wear eye protection. String plugs installed from the outside are often considered temporary roadside fixes rather than proper repairs. A shop setup typically includes a tire spreader, a liner scraper and vulcanizing cement along with the air tools. Keep the buffer's speed within the patch maker's recommendations so the rubber texture is correct for bonding.
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.