Store relaunching soon · pro diagnostics & tools for independent shopsjoseph@directtoolsource.com
Direct Tool SourcePro Diagnostics
Home / Answers / OBD-II & Trouble Codes / Ignition, Oxygen Sensor and Emissions Codes

Ignition, Oxygen Sensor and Emissions Codes

Coil, oxygen sensor, catalyst, secondary air and EVAP circuit codes explained.

23 answers · last reviewed 2026-11-16

What does P0440 EVAP system malfunction mean?

Short answer: P0440 is a general EVAP fault that some vehicles use for a leak or a component problem in the evaporative system; check service information for how that vehicle defines and tests it.

P0440 is a broad code for the evaporative emission system, the system that captures fuel vapor from the tank and burns it in the engine. Some vehicle makers use it for a leak, others for a fault in a valve or sensor.

Start with simple items: a loose or damaged gas cap or capless filler seal, cracked hoses, and damaged lines near the tank. Then use a scan tool to command the purge and vent valves and watch the tank pressure sensor respond.

A smoke machine is the best tool for finding leaks. Seal the system with the scan tool's EVAP service function or by closing the vent valve, introduce smoke and look for where it escapes. Keep ignition sources away from the fuel system and work in a ventilated area.

Tools used for this job

Thinkcar 310010006 PLD212 EVAP Smoke MachineMastercool 43065 Dual Evap and High Pressure Smoke Machine Kit

What does P0451 EVAP pressure sensor range or performance mean?

Short answer: The fuel tank pressure sensor reading does not make sense for the conditions, often from a failing sensor, a wiring or connector issue, or a blocked or disconnected sensor hose.

The EVAP pressure sensor, often mounted on or near the fuel tank, reports small pressure and vacuum changes. P0451 means its reading was implausible, such as not reading zero with the system vented, or not changing when the purge valve opened.

With the engine off and the gas cap removed, the sensor should read close to zero. If it does not, check the reference voltage, ground and signal at the sensor. Look for a kinked or disconnected hose on sensors that use one.

Watch the sensor while commanding the purge and vent valves to see if it responds. The sensor is often near the tank, so support the vehicle on a lift or rated stands, and keep sparks away from the fuel system.

Tools used for this job

Autel MS906MAX OBDII Bi-Directional Diagnostic ScannerFluke 1567573 TP40 Automotive Back Probe Pin Set

What does code P0030 mean?

P0030 means a problem in the heater control circuit for the upstream oxygen sensor on bank 1; check the heater fuse, the sensor heater resistance and the wiring.

Read the full answer →

What does code P0130 mean?

P0130 means the upstream oxygen sensor on bank 1 is not showing the expected signal; check for exhaust leaks, wiring damage and the sensor's response on a scan tool.

Read the full answer →

What does code P0411 mean?

P0411 means the secondary air injection system did not change the oxygen sensor reading as expected; common causes are a failed air pump, stuck check valves, leaking hoses or a bad relay.

Read the full answer →

What does code P0449 mean?

P0449 means a problem in the EVAP vent valve or solenoid control circuit, often from a failed vent solenoid, damaged wiring or corrosion near the charcoal canister.

Read the full answer →

What does code P0036 mean?

P0036 means a problem in the heater control circuit for the downstream oxygen sensor on bank 1; check the heater fuse, wiring and sensor heater resistance.

Read the full answer →

What does code P2457 mean?

P2457 means the exhaust gas recirculation cooling system is not performing as expected, often from a clogged or leaking EGR cooler or a temperature sensor problem.

Read the full answer →

General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.