Store relaunching soon · pro diagnostics & tools for independent shopsjoseph@directtoolsource.com
Direct Tool SourcePro Diagnostics
Home / Answers / Scan Tools & Bi-Directional Controls / Service Resets & Special Functions

Service Resets & Special Functions

Oil resets, EPB, SAS, battery registration, throttle and injector relearns.

21 answers · last reviewed 2026-11-16

What is a cooling system air purge or bleed routine on a scan tool?

Short answer: Some vehicles with electric coolant pumps or valves need a scan tool to run the pumps and open valves in a set sequence so air is removed after coolant service.

Traditional cooling systems bleed air with the engine running and the thermostat opening. Newer designs with electric water pumps, coolant control valves and several separate loops can trap air that the engine alone will not push out. For these, the vehicle maker may specify a bleed routine run from a scan tool, which commands pumps and valves in sequence.

Skipping the routine can leave air pockets that cause overheating, poor heater output or warning lights, especially in hybrid and EV thermal systems.

Look up the coolant fill and bleed procedure for the vehicle. Use a vacuum fill tool if the procedure allows. Keep the system cool before opening it, because hot coolant under pressure can cause serious burns. Confirm your scan tool supports the routine for that model before starting.

Tools used for this job

Autel MS906MAX OBDII Bi-Directional Diagnostic ScannerAutel MS919S2 MaxiSYS MS919 S2 Tablet with VCMI2

What is an air suspension calibration on a scan tool?

Short answer: It is a procedure that teaches the suspension module the correct ride height after a sensor, strut, compressor or module is replaced, using measured heights entered into the scan tool.

Vehicles with air suspension or electronically controlled ride height use height sensors at each corner. When a sensor, air spring, control arm or module is replaced, the module needs to learn the correct height values again. The calibration usually involves measuring ride height at specified points and entering the measurements, or lowering and raising the vehicle through a scan tool routine.

Follow the vehicle maker's procedure closely, including tire pressures, fuel level, load, and measurement points. Wrong values can leave the vehicle sitting too high or low, which affects handling, headlight aim and ADAS sensors.

Air suspension can drop suddenly when lines are opened or the system is commanded. Put the vehicle on a lift or rated stands and never place hands or tools under the body while the suspension is moving.

Tools used for this job

Autel MS919S2 MaxiSYS MS919 S2 Tablet with VCMI2Autel ULTRAS2 MaxiSYS ULTRA S2 Diagnostic Scan Tool

What is an electric power steering initialization?

Short answer: After some steering repairs, the power steering module must learn its end stops or center position through a scan tool or a specific steering sequence before steering assist and related systems work normally.

Electric power steering systems use sensors to know where the steering is and how much assist to provide. After a rack, column, module or battery service on some vehicles, the system loses that information. Warning lights may appear, assist may be reduced, or steering may feel uneven left to right.

An initialization teaches the module the steering limits and center. Some vehicles do this with a sequence of turning lock to lock with the engine running. Others need a scan tool routine. A steering angle sensor calibration is often part of the same job.

Follow the vehicle maker's procedure in order, since alignment may need to be done first. Keep the vehicle stationary and the area clear while turning the wheel through its range, and road test carefully to confirm assist and stability systems are working.

Tools used for this job

Autel MS906MAX OBDII Bi-Directional Diagnostic ScannerLaunch 702020112TF X613 Mobile Wheel Aligner with X431 Throttle Tablet and

What is a clutch adaptation on a dual-clutch transmission?

Short answer: It is a scan tool procedure that teaches the transmission computer the engagement points of its clutches, usually required after clutch, mechatronic or software work, and sometimes to cure rough shifting.

Dual-clutch transmissions use computer-controlled clutches instead of a torque converter. The computer must know exactly where each clutch begins to engage. After replacing clutches, the mechatronic unit, or updating software, these values must be learned again.

The adaptation runs through a scan tool. It often requires specific conditions, such as transmission fluid temperature within a range, the engine idling, and the brake applied, followed by a road test. Some vehicles need several steps in order.

Look up the procedure for the transmission and confirm your scan tool supports it. Secure the vehicle with the parking brake and wheel chocks during stationary steps, and road test carefully to confirm smooth engagement.

Tools used for this job

Autel MS919S2 MaxiSYS MS919 S2 Tablet with VCMI2Autel ULTRAS2 MaxiSYS ULTRA S2 Diagnostic Scan Tool

How do I update a vehicle's tire size or axle ratio setting?

Short answer: Many vehicles store tire size and axle ratio in a module, and a scan tool with configuration functions can update them so the speedometer, transmission shifting and stability systems use correct values.

When a customer installs larger or smaller tires, or changes the axle ratio, the vehicle's computers still use the original values. The speedometer reads wrong, shift points change, and stability control and ADAS systems may react incorrectly.

On many vehicles, tire size and axle ratio are stored as configuration values. A scan tool with configuration functions, or the vehicle maker's software, can update them. Some vehicles allow only certain sizes, and some need a dealer-level tool.

Measure or look up the actual tire size, enter values exactly as the procedure describes, and verify speedometer accuracy afterward with a GPS speed check during a careful road test. Check whether ADAS calibration is needed after the change.

Tools used for this job

Autel MS909S2 MaxiSYS MS909 S2 Tablet with VCI2Autel MS906MAX OBDII Bi-Directional Diagnostic Scanner

What are on-demand self-tests on a scan tool?

Short answer: On-demand self-tests are routines where the engine computer checks its own circuits and components while the engine is off or running, reporting any faults found during the test.

Some vehicle makers provide self-test routines that the scan tool starts. With the key on and engine off, the computer checks sensor circuits and outputs. With the engine running, it checks system response, such as idle control or sensor changes. Faults found during the test show as codes.

These tests catch issues that may not set codes during normal driving, and they confirm repairs. Availability depends on the vehicle maker and the scan tool's coverage.

Follow the instructions on the scan tool: some tests require you to press the brake, turn the steering wheel or snap the throttle at specific moments. Set the parking brake, chock the wheels and keep the area clear when running engine-running tests, and never leave the vehicle unattended during a test.

Tools used for this job

Autel MS906MAX OBDII Bi-Directional Diagnostic ScannerTopdon TDONEPLUS ONE Plus 10.1" Automotive Diagnostic Scan Tool Bundle

General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.