Air Hammers and Chisels
Choosing air hammers, shank sizes, retainers and bits for suspension, exhaust and body work.
Can an air hammer install bearing races and seals?
Short answer: Pneumatic race and seal drivers made for air hammers can install bearing races and seals quickly, but they must fit correctly and be driven squarely to avoid damage.
Race and seal driver sets include discs or adapters sized for common bearings. Mounted on an air hammer, they drive races into hubs or housings.
Ensure the race or seal starts square, and use the correct driver size. Drive gently and check progress often.
Over-driving can damage races, seals or housings, and a cocked race can gouge the bore. Stop when the sound changes to a solid ring, which usually means the race has bottomed, then check it visually all the way around. Some components require a press or specific tools, so follow the service information. Wear eye and hearing protection.
Tools used for this job
What is a needle scaler and how is it different from an air hammer?
Short answer: A needle scaler uses a bundle of steel needles driven by an air piston to remove rust, scale, paint and weld slag from rough surfaces, while an air hammer drives a single bit for cutting and punching.
Needle scalers are useful on frames, castings, welds and steel structures. The needles conform to uneven surfaces and knock off scale.
Air hammers are better for cutting, punching and separating parts. Some needle scalers can switch to a chisel attachment.
Needle scalers use more air than many small tools, so check the maker's air requirement, and replace needles as a set when they wear short. They create dust and noise. Wear eye, hearing and respiratory protection, especially if removing old paint that may contain lead, and clean up dust with a HEPA vacuum rather than blowing it around.
Tools used for this job
What are tapered punch bits for an air hammer used for?
Short answer: Tapered punch bits drive out pins, rivets, bolts and bushings, starting with a narrow tip to fit the hole and widening to resist bending under heavy blows.
Tapered punches come in various diameters and lengths. They are useful for driving roll pins, rivets and seized bolts.
Choose a punch that fits the hole without binding. Start with a smaller punch and move up as the pin moves.
Keep the punch straight, and avoid side loading, which bends the tip. A tapered punch is good for starting a pin, but once the pin moves, switch to a straight pin punch to drive it fully out, since a taper can wedge in the hole. Replace mushroomed or chipped punches. Wear eye and hearing protection.
Tools used for this job
Can I use an air chisel on cast iron parts?
Short answer: Use caution, because cast iron is brittle and can crack under air chisel blows, so use light pressure, avoid striking thin sections and consider other methods for valuable parts.
Cast iron components like exhaust manifolds, brake drums and some brackets can crack from sharp impacts. An air chisel can damage them quickly.
If you need to remove rusted fasteners or scale from cast iron, use penetrating oil, heat or a needle scaler instead of heavy chiseling.
Cutting through cast iron with an air chisel is possible but rough, and the part will usually crack unpredictably. If the part is being scrapped anyway, cracking it can be a quick way to free a seized stud or bolt. Wear eye protection, as cast iron chips can fly.
Tools used for this job
Can I use an air hammer to break concrete?
Short answer: A standard automotive air hammer can chip small amounts of concrete, but it is not designed for breaking slabs, so use a rotary hammer or demolition hammer for real concrete work.
Automotive air hammers are light and designed for metal work. They can chip concrete edges or remove thin layers.
For larger jobs, demolition hammers or chipping hammers made for concrete are more effective and less likely to damage the tool. Concrete is abrasive and wears bits quickly, and the constant shock can loosen an automotive hammer's retainer and wear its piston. Renting the right tool is often cheaper than repairing an air hammer.
Concrete dust contains silica. Use water to control dust, wear a properly fitted respirator rated for silica, and wear eye, hearing and hand protection.
Can an air chisel separate spot-welded body panels?
Short answer: An air chisel with a panel separator or spot weld chisel can split panels apart after the welds are drilled or ground, but chiseling through intact welds tears metal, so drill the spot welds first whenever the panel underneath is being kept.
Collision repair procedures usually call for drilling out spot welds with a spot weld cutter, then separating the panels. A thin, wide panel separator bit in an air chisel slides between the flanges and pops any remaining weld nuggets free.
Driving a chisel through intact welds rips holes in the flange you want to keep, which then needs extra welding. If the outer panel is scrap, chiseling through it is faster, but protect the inner panel.
Follow the vehicle maker's repair procedures, as some high-strength steels must not be heated or cut in certain areas. Wear eye and hearing protection, gloves for sharp edges, and keep fingers away from the bit.
Tools used for this job
How do I change an air hammer bit safely?
Short answer: Disconnect the air hose first, then remove the spring retainer or release the quick-change collar, swap the bit and confirm it is locked before reconnecting the air.
An air hammer can fire a loose bit out of the barrel with a lot of force if the trigger is bumped while the retainer is off. Disconnecting the air removes that risk completely.
With a spring retainer, unscrew the spring from the barrel, remove the old bit, insert the new bit and thread the spring back on fully until it is snug. With a quick-change chuck, pull the collar, insert the bit until it clicks, and tug on it to confirm it is held.
Inspect the bit's shank and collar for cracks and mushrooming before installing. Never point the hammer at anyone when reconnecting air, and wear eye protection.
Tools used for this job
Why does my air hammer only tap lightly instead of hitting hard?
Short answer: Weak hitting usually comes from low inlet pressure, a restrictive hose or coupler, a dry or worn piston and barrel, a sticky valve or a bit that is not seated against the work.
Air hammers need steady pressure and flow to cycle the piston at full force. Check the pressure at the tool while it runs. A small hose or several adapters in line can starve it.
Oil the hammer, since a dry piston drags in the barrel. If it still runs weak, the piston or barrel may be worn or scored, or the valve may be sticking from dirt or water.
Also make sure you are pressing the bit firmly against the work. Many hammers are designed to cycle properly only under load. Disconnect the air before disassembly, and if internal parts are worn, a rebuild kit or professional repair may be needed. Wear eye and hearing protection when testing.
Tools used for this job
How do I separate a rusted exhaust slip joint with an air hammer?
Short answer: Remove the clamp, soak the joint with penetrating oil, then use a flat chisel or a tailpipe splitter bit to open the outer pipe's seam, or vibrate the joint with a blunt bit while twisting the pipe.
Slip joints rust together, and pulling them apart often tears the pipe. If the outer pipe is being replaced, splitting it lengthwise with an air chisel lets the inner pipe slide out cleanly.
Cut carefully along the outer pipe without gouging the inner pipe you want to keep. A few cuts at different points around the circumference make it easier to peel the outer pipe away.
If both pipes stay, vibrating the joint with a blunt bit can break the rust bond enough to twist it apart. Let the exhaust cool fully first, wear gloves for sharp edges and rust, and wear eye protection, since rust flakes fall when working overhead.
Tools used for this job
What is a panel cutter bit for an air hammer?
Short answer: A panel cutter bit has a forked or curved cutting tip that slices sheet metal as the hammer pushes it forward, leaving a cut that is cleaner than a plain chisel but rougher than a saw or nibbler.
Panel cutter bits are used for rough cuts in body panels, floor pans and sheet metal during rust repair and salvage. The forked shape guides the metal between the tips to shear it.
They work best on thin gauge steel. Thicker metal or curved sections may be easier with a cut-off tool, air saw or nibbler.
Mark your line, start the cut at a hole or edge, and keep steady forward pressure. The cut edge will be sharp and may need trimming. Watch for wiring, fuel lines and brake lines behind the panel. Wear eye protection, hearing protection and cut-resistant gloves.
Tools used for this job
What are soft head air hammer bits used for?
Short answer: Soft head bits use a nylon, brass or rubber tip to deliver air hammer blows without marring the surface, which helps when seating parts, tapping out dents or loosening parts you want to keep.
Steel bits leave dents and gouges. Soft heads spread the impact and protect surfaces such as aluminum, finished steel and painted panels.
They are useful for seating trim, tapping wheels loose from hubs without damaging the wheel face, driving parts into place and light body work. Some sets include interchangeable tips.
Soft tips wear faster than steel, so replace them when they split or mushroom. They still deliver a strong force, so control the throttle and avoid hitting fragile parts too hard. Wear eye and hearing protection.
Tools used for this job
Can I use an air hammer on aluminum parts?
Short answer: Use care, because aluminum is softer than steel and an air hammer can dent, gouge or crack it, so use soft head bits, low pressure and light blows when working near aluminum components.
Many modern vehicles use aluminum control arms, knuckles, subframes and engine parts. A steel chisel or punch can damage these quickly.
When driving a steel bolt out of an aluminum part, use a punch slightly smaller than the bolt, support the part and keep the punch straight so it does not hit the aluminum bore. Heat and penetrating oil may help with corrosion between steel and aluminum.
Avoid hammering directly on thin aluminum castings or ball joint bosses. If damage occurs, the part may need replacement. Wear eye and hearing protection.
Tools used for this job
How do I drive out a wheel stud with an air hammer?
Short answer: Support the hub from behind, use a flat punch slightly smaller than the stud, and drive it straight out, but check the service information first, as some hubs require a press tool to protect bearings.
Wheel studs are pressed into the hub flange. Many can be driven out with a hammer or air hammer, but heavy blows can damage wheel bearings on some hub designs.
Remove the brake rotor or drum if needed for access. Thread an old nut flush with the stud end to protect it if you might reuse it, though replacement is usually best.
Install the new stud with a stud installer or a stack of washers and a lug nut, pulling it into the flange fully. Do not hammer new studs in. Torque lug nuts properly and wear eye protection.
Tools used for this job
Is an air hammer the same as an air chisel?
Short answer: In automotive use, air hammer and air chisel usually mean the same tool, a pneumatic hammer that drives interchangeable bits, though some people reserve air chisel for the tool when fitted with cutting bits.
The tool has a piston that strikes the bit shank rapidly. With a chisel bit, it cuts metal and splits joints. With a punch, it drives pins and bolts. With other bits, it separates ball joints and smooths metal.
Industrial chipping hammers and demolition hammers are larger tools for concrete and stone, not the same as automotive air hammers.
When buying bits, match the shank size and type, typically .401 or .498 for automotive tools. Always use a bit retainer, and wear eye and hearing protection.
Tools used for this job
Can I use an air chisel to cut through welds?
Short answer: An air chisel can split tack welds and thin weld beads when separating parts, but heavy structural welds are better cut with a cut-off wheel or grinder.
When removing brackets, hangers or patch panels that were tack welded, a sharp, narrow chisel bit concentrates the hammer's force on the weld and can pop it loose quickly. Angle the bit so it drives between the parts rather than straight into the weld bead.
Heavy welds on frames, hitches or structural parts resist chiseling, dull the bit and can tear the base metal. A thin cut-off wheel or a grinder gives a cleaner, more controlled cut on those.
Check what is behind the weld before cutting, including fuel lines, brake lines and wiring. Grind any remaining weld flush afterward if the part is being reused. Wear eye and hearing protection and gloves, since freshly cut edges are sharp.
Tools used for this job
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.