Air Hammers and Chisels
Choosing air hammers, shank sizes, retainers and bits for suspension, exhaust and body work.
Why does the striking end of my air hammer bit mushroom?
Short answer: Mushrooming happens when the bit's shank end deforms from repeated piston hits, usually because the bit is soft or worn, the hammer is fired without the bit loaded against the work, or pressure is too high.
Inside the barrel, the piston strikes the end of the bit shank thousands of times a minute. Quality bits are heat treated so the shank end stays hard enough to resist spreading.
When a shank mushrooms, it can bind in the barrel, making the bit hard to remove, and it can crack and throw chips. Firing the hammer with the bit not pressed against the work lets the piston slam the shank with nothing absorbing the energy, which speeds up the damage.
Replace bits with mushroomed shanks rather than grinding them, unless the bit maker says dressing is allowed. Keep the working tip in good shape too, since a mushroomed cutting end can chip. Wear eye protection whenever you run the hammer.
Tools used for this job
Can I use hand chisels in an air hammer?
Short answer: No, hand chisels lack the correct shank, collar and heat treatment for air hammers, and they can shatter or be thrown out of the barrel, so use only bits made for your hammer's shank size.
Air hammer bits have a precise shank diameter, commonly .401 or .498 inch, plus a collar or flange that the retainer grips. That design keeps the bit aligned with the piston and stops it from flying out.
A hand chisel has no collar, so the retainer cannot hold it, and its shank will not fit the bore correctly. It is also hardened for occasional hand blows, not thousands of high-speed strikes, so it can crack or shatter.
Using the wrong tool can damage the hammer's barrel and piston too. Buy bits designed for your hammer, match the shank type to the retainer, and keep a small set of the shapes you use most. Wear eye protection, because a failed bit can throw fragments.
Tools used for this job
How do I free a strut from a pinch-bolt knuckle with an air hammer?
Short answer: Remove the pinch bolt, open the knuckle slot slightly with a knuckle spreader, then use a blunt air hammer bit on the knuckle near the strut to shake the rust bond loose.
Many MacPherson struts slide into a split knuckle clamped by a pinch bolt. Corrosion between the strut tube and the knuckle can make it very hard to separate.
After removing the bolt, a knuckle spreader tool inserted into the slot and turned a quarter turn opens the clamp slightly. Apply penetrating oil, then use a blunt bit on the knuckle body to vibrate it while pulling down on the knuckle.
Do not pry against the strut tube or hammer on it, and keep the bit away from brake lines, ABS wiring and the axle boot. Support the knuckle so it does not swing out and stretch the brake hose. Wear eye protection, and make sure the vehicle is supported safely on a lift or stands.
Tools used for this job
Should I use an air hammer to install press-fit ball joints or bushings?
Short answer: No, press-fit ball joints and bushings should be installed with a press or the correct installer tools, because hammering can crack housings, damage the part and leave it seated crooked.
Press-fit parts are designed to be pushed into their bore evenly and steadily. An air hammer drives them in sharp jolts, which can cock the part in the bore, gall the bore, crack a cast housing or tear rubber bushings.
Use a C-frame ball joint press, a bushing installer set or a hydraulic press with adapters that support the part on the correct surfaces. Check the service information for installation depth, orientation and whether the bushing should be tightened at ride height.
Install any retaining clips or snap rings fully, and confirm the part is square in the bore. Wear eye protection when using a press, as parts and adapters can shoot out under load.
Can I use an air hammer to free a seized caliper slide pin?
Short answer: An air hammer with a small punch can help drive out a seized slide pin, but protect the boot and bracket bore, and replace pins, boots or the bracket if they are corroded.
Caliper slide pins can seize in the bracket from rust and dried or wrong grease, which causes uneven pad wear and dragging brakes. Once the caliper bolt is out, a punch on the end of the pin can drive it free.
Support the bracket so the blows do not stress the knuckle, apply penetrating oil and use short bursts. Many pins have a rubber bushing or boot that will be damaged, so plan to replace it.
Clean the bore thoroughly, and lubricate new pins with a brake grease made for slide pins. If the bore is pitted, replace the bracket. Wear eye protection, and avoid breathing brake dust, using a brake cleaner and wet wiping instead of blowing it off.
Tools used for this job
How do I remove a seized clevis or hitch pin with an air hammer?
Short answer: Remove any clips or cotter pins, support the clevis, then use a straight punch slightly smaller than the pin to drive it out with short bursts of the air hammer.
Clevis pins on trailer couplers, tow equipment, hydraulic cylinders and farm implements rust in place easily. Penetrating oil, a few minutes of soak time and the hammer's vibration usually free them.
Supporting the clevis on both sides of the pin keeps you from bending the ears. Start with a tapered punch to break the pin loose, then switch to a straight pin punch so it does not wedge in the bore. Keep the punch aligned with the pin to avoid mushrooming the end.
Replace damaged pins with the correct diameter and grade, and grease them on reassembly. If the pin holds a load, such as a cylinder or implement, block or support the load first. Keep hands out of pinch points and wear eye protection.
Tools used for this job
What makes a super duty air hammer different from a regular-duty one?
Short answer: Super duty air hammers are generally built heavier, with sturdier barrels, pistons and retainers for frequent hard use, but the exact differences vary by maker, so compare their published specifications.
Regular-duty hammers suit lighter cutting, occasional suspension work and body jobs. Super duty models target daily heavy work like separating suspension joints, cutting thick exhaust and driving large pins.
Makers may use different stroke lengths, piston sizes, barrel materials and retainer designs to reach that duty level. Those changes can mean harder hits, but also more weight, vibration and air use.
Compare blows per minute, stroke length, shank size, weight, vibration data and air consumption from the maker's specifications rather than relying on the name. Choose based on the work you do most, and buy quality bits to match. Wear eye and hearing protection, and consider anti-vibration gloves for long sessions.
Tools used for this job
How do I protect painted surfaces when using an air hammer nearby?
Short answer: Cover nearby painted surfaces with heavy tape, fender covers or a metal shield, use soft head bits where possible, and control the hammer with both hands so a slip does not gouge the finish.
An air hammer that skates off a rusty bolt can chip paint, dent a panel or scratch chrome in an instant. A little preparation prevents expensive touch-up.
Apply several layers of masking or protective tape around the work area, and lay fender covers over adjacent panels. For close work, a thin sheet metal or plastic shield held between the bit and the paint absorbs slips. Choose a bit shape that seats securely on the work, and start at low pressure.
Rust chips and metal fragments also scratch paint, so brush them away rather than wiping across the surface. Wear eye protection, as debris flies in all directions.
Tools used for this job
Can I use a .401 bit in a .498 air hammer?
Short answer: No, .401 and .498 describe different shank diameters, and a .401 bit will not fit or be retained properly in a .498 hammer, so always use bits that match the hammer.
The numbers refer to the bit shank diameter in inches. The hammer's barrel bore and retainer are sized for one shank. A smaller bit in a larger bore will not align with the piston, and the retainer may not hold it.
That misalignment can damage the piston and barrel, and the bit can be thrown out of the tool. Adapters for this purpose are not common for automotive hammers, and an improvised sleeve is not safe.
If you own both sizes of hammer, store their bits separately and label them. Check the collar style too, as retainers differ between round and hex collars and between makers. Wear eye protection whenever you run an air hammer.
Tools used for this job
How do I use an air hammer safely near brake lines and wiring?
Short answer: Find and shield brake lines, fuel lines and wiring before you start, keep the bit pointed away from them and use short controlled bursts, since a slip can crush a line or cut a wire.
Hard brake and fuel lines are thin steel tubing, and an air hammer bit can kink or puncture them with one slip. Wiring harnesses and ABS sensor leads are just as easy to damage.
Trace where lines run before setting the bit. Unclip lines and wiring and move them aside where possible, or slip a piece of scrap metal or a pry bar between them and the work as a guard. Choose a bit shape that seats firmly so it is less likely to skate.
After the job, inspect nearby lines and wiring for dents, chafing and cuts. A damaged brake line must be replaced, not taped. Wear eye protection, and keep the work area clear of other people.
Can I use an air hammer to free a seized brake drum?
Short answer: Use care, because drums are cast iron and can crack, so back off the adjuster, use a soft head bit or blunt bit on the drum face between the studs, and switch to a drum puller if it will not move.
Brake drums rust to the hub or axle flange, and worn shoes can catch on the ridge inside a worn drum. Before applying force, remove any retaining clips and back off the self-adjuster through the access slot.
Soak the hub area with penetrating oil, then use light blows on the drum face between the wheel studs with a soft head bit. Rotate the drum and repeat. Do not hit the drum's outer edge or lip, which can crack or chip.
If it still sticks, a drum puller applies even force without damage. Inspect the drum for cracks before reusing it. Wear eye protection, and avoid breathing brake dust by wetting it down rather than blowing it off.
Tools used for this job
How do I start an air chisel cut without the bit skating?
Short answer: Mark the line, start with the bit at a steep angle and low throttle until it bites, then lower the angle and increase power, keeping firm pressure so the bit stays in the groove.
Smooth or rounded surfaces give the bit nothing to grip, and it can jump off and damage nearby parts. A small starting notch made with a file, a center punch or a quick nick with a cut-off wheel gives the bit a place to seat.
Feather the throttle at first, then increase pressure once the cut has started. Steer with a support hand near the front of the hammer and keep the bit in line with the cut.
A sharp bit skates less than a dull one, so dress or replace cutting bits as they wear. Stop and reposition rather than forcing a bit that keeps sliding. Wear eye and hearing protection, and keep your support hand behind the cutting edge.
Tools used for this job
What causes an air hammer retainer spring to break?
Short answer: Retainer springs usually break from firing the hammer without the bit loaded against the work, worn or wrong-size springs, overtightening, and running at excessive pressure.
The retainer spring holds the bit in the barrel and takes a hit every time the bit rebounds. When the hammer runs with no resistance, the bit slams forward against the spring repeatedly, which fatigues the coils.
A spring that is stretched, the wrong size for the bit collar or not threaded fully onto the barrel also fails faster. Cracks usually start at the last coils.
Inspect the spring when changing bits and replace it at the first sign of cracking or stretching, since a broken retainer can let the bit fly out. Keep the bit against the work before pulling the trigger and run at the maker's recommended pressure. Wear eye protection at all times when using the hammer.
Tools used for this job
How can I reduce air hammer noise in a home garage?
Short answer: Use the lowest pressure that does the job, keep the bit firmly loaded, work in short bursts, close the garage door and add rubber mats or sound absorbing panels, and always wear hearing protection.
Air hammers are among the loudest tools in a garage, and the noise travels to neighbors and the house. You cannot make one quiet, but you can reduce the impact.
A loaded bit makes less noise than one chattering against the work. Lower pressure reduces both noise and vibration. Work at reasonable hours, and consider alternatives for some jobs, such as a hand saw, a nibbler or a press, which are quieter.
Rubber floor mats and absorbent wall panels reduce echo inside the garage. Keep the compressor in a separate space if possible, since it adds to the noise. Earmuffs or earplugs rated for the noise level are essential for anyone nearby.
Tools used for this job
Should I use an air hammer to remove old gaskets?
Short answer: Not on aluminum or precision sealing surfaces, which an air scraper can gouge, but a scraper bit can remove heavy gasket material from cast iron or rough steel flanges if you work carefully.
Cylinder heads, intake manifolds, oil pans and timing covers often have aluminum sealing surfaces. Gouges from a steel scraper bit can cause leaks, and some surfaces must be flat within tight limits.
For aluminum, use a plastic scraper, gasket remover chemical and a fine abrasive pad made for gasket surfaces, following the engine maker's guidance about abrasives and debris.
On cast iron exhaust flanges or heavy steel brackets, a scraper bit at a low angle and low pressure can speed removal. Keep debris out of engine openings by stuffing rags in ports and passages. Wear eye protection and gloves.
Tools used for this job
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.