Air Drills, Riveters and Specialty Air Tools
Pneumatic drills, rivet and rivet nut tools, grease guns, needle scalers, slide hammers, caulking guns, windshield tools and other specialty air tools.
Is an air drill better than a cordless drill?
Air drills are light, compact, run continuously without overheating and have no batteries to charge, but they need a compressor and hose and use a lot of air, so cordless drills are often more convenient for occasional drilling.
Read the full answer →What is the difference between a 3/8-inch and 1/2-inch air drill?
Short answer: The number refers to chuck capacity; 3/8-inch air drills are usually lighter and faster for small holes, while 1/2-inch drills are geared lower for more torque with larger bits, hole saws and step drills.
Chuck size limits the largest bit shank you can use, but the bigger difference is gearing. A 3/8-inch air drill typically spins faster and is lighter, which suits sheet metal, small pilot holes and body work. Many 1/2-inch drills run at lower speed with more torque, which suits larger twist drills, hole saws and step bits in thicker steel.
Speed and torque ratings vary by model, so compare the maker's free speed and torque specs. Low-speed, high-torque drills can twist hard if a bit catches, so use the side handle when provided.
Clamp workpieces, use sharp bits and cutting fluid in steel, wear safety glasses and keep hands clear of the chuck. Let the drill do the work rather than forcing it.
Tools used for this job
Why does my air drill slow down under load?
Short answer: An air drill that bogs down is usually starved for air from a small hose, restrictive coupler or undersized compressor, or it needs oil, has worn vanes or is running a dull bit.
Air motors lose speed and torque quickly when supply pressure drops under flow. Check the pressure at the tool inlet while it runs. Long, small-diameter hoses and small couplers can cause a large drop. Use the hose and fittings the maker recommends.
Lack of lubrication increases friction, and worn or sticky vanes reduce power. Add a few drops of air tool oil and run the tool briefly. If performance does not improve, the motor may need cleaning or a rebuild.
A dull bit or the wrong speed for the material also loads the drill. Use sharp bits and cutting fluid. Disconnect air before changing bits, and wear eye protection.
Tools used for this job
How does a pneumatic rivet gun work?
Short answer: A pneumatic blind rivet tool uses air pressure, often through a hydraulic intensifier, to pull the rivet mandrel until it breaks, setting the rivet faster and with less effort than a hand riveter.
Blind rivets, often called pop rivets, are set by pulling a mandrel through the rivet body until the body expands and the mandrel snaps. Hand riveters require squeezing the handles several times. Air riveters do it with a trigger pull.
Many air riveters use an air-over-hydraulic design for the pulling force. Some include vacuum mandrel collection that holds rivets in the nose and draws spent mandrels into a container.
Choose a tool rated for the rivet diameter and material you use, and install the correct nosepiece. Wear safety glasses, since mandrels can eject. Keep the collection bottle in place and empty it regularly.
Tools used for this job
What is a pneumatic rivet nut tool used for?
Short answer: A rivet nut tool installs threaded inserts into sheet metal or tubing from one side, creating strong threads where a regular nut cannot be reached or the metal is too thin to tap.
Rivet nuts, sometimes called nutserts, are installed by threading them onto a mandrel, inserting them in a drilled hole and pulling until the body collapses behind the panel. The result is a permanent threaded insert.
They are used for mounting accessories, trim, racks and panels on vehicles and equipment. Pneumatic setters speed up installation and reduce hand fatigue.
Use the correct mandrel and nose for each thread size, set stroke or pressure per the maker's instructions and drill the specified hole size. Wear safety glasses and keep fingers away from the nose.
Tools used for this job
How does an air grease gun work?
Short answer: An air grease gun uses shop air to drive a piston pump that pushes grease through the hose with each stroke, either continuously while the trigger is pulled or one shot at a time, saving hand effort on heavy greasing jobs.
Manual grease guns require repeated lever pumping. Air-operated guns use a pneumatic motor or piston to pump grease automatically. Continuous-flow models deliver grease as long as the trigger is held, while some designs deliver a shot per trigger pull.
They are popular for fleets, farm equipment and heavy machinery with many grease points. They can produce high grease pressure, so control the amount to avoid blowing out seals.
Use the grease specified by the equipment maker, prime the gun after loading a new cartridge and check fittings for blockages. Never point the coupler at your body, since high-pressure grease injection can cause serious injury. Disconnect air before changing cartridges.
Tools used for this job
How do I avoid blowing out seals with an air grease gun?
Short answer: Watch the seal or boot while greasing and stop as soon as it starts to swell or fresh grease appears, since air grease guns can build much higher pressure than needed.
Many components, such as ball joints, tie rod ends and U-joints, have rubber boots or seals. Too much grease pressure can rupture them, letting dirt in and grease out.
Apply grease in short bursts, observe the boot and stop when it begins to expand or old grease is purged. Some fittings are designed to vent through a relief.
Follow the equipment maker's lubrication guidance for quantity and intervals. If grease will not enter, clean or replace the fitting rather than forcing it. Wear eye protection and gloves, and keep your hands away from the coupler tip while it is under pressure.
Tools used for this job
When should I use a needle scaler instead of a wire wheel?
Short answer: Choose a needle scaler for heavy scale, weld slag and pitted or irregular steel, because its air-driven needles follow uneven shapes; a needle scaler uses a bundle of hardened needles driven by an air piston to knock off rust, scale, weld slag and old coatings, especially on rough or uneven steel surfaces.
Needle scalers hammer the surface with many small needles. Because the needles conform to irregular shapes, they work well on frames, welds, castings and pitted steel where a wire wheel or grinder cannot reach evenly.
They are common in fabrication, heavy equipment repair and marine work. Some models can switch to a chisel attachment for flat surfaces.
Scalers are loud and generate flying debris and vibration. Wear safety glasses or a face shield, hearing protection, gloves and a respirator if removing old coatings that may contain lead. Replace worn needles as a set.
Tools used for this job
Can an air slide hammer pull a stuck axle or hub?
Short answer: Often yes; an air slide hammer uses a pneumatic hammer mechanism to deliver repeated pulling blows, helping remove stuck axles, hubs, bearings and seals faster than a manual slide hammer.
Manual slide hammers rely on you sliding a weight to create a pulling impact. Air slide hammers deliver rapid blows from compressed air, often making it easier to pull seized parts.
They are commonly used with adapters for axles, hubs, bearings and seals. Choose adapters rated for the job and attach them securely.
Wear eye protection, keep your body out of line with the tool in case an adapter breaks loose, and support the vehicle on rated stands. Check that the part is fully released from bolts or clips before pulling.
Tools used for this job
How does an air windshield removal tool work?
Short answer: An air windshield removal tool oscillates a sharp blade to cut through urethane adhesive around the glass, reducing effort compared to manual knives and wires.
Modern windshields are bonded with urethane. Cutting the urethane manually is physically demanding. Air-powered tools use oscillating blades that cut through the adhesive with less effort.
Blades come in different shapes to reach around the pinchweld. Protect the dashboard and paint, and use care around sensors and trim.
Wear cut-resistant gloves and safety glasses. Follow the glass maker's procedures for removal and installation, and recalibrate ADAS cameras as needed. Air knives with reciprocating or oscillating action can also cut through urethane on rear glass and quarter windows, but some vehicles use encapsulated glass with clips that need special handling.
Tools used for this job
What is a pneumatic caulking gun used for?
Short answer: A pneumatic caulking gun uses air pressure to dispense seam sealer, adhesive or caulk from cartridges smoothly and consistently, reducing hand fatigue for long beads.
Body shops use pneumatic caulking guns for seam sealer, panel adhesives and undercoatings. Air pressure provides a steady bead, which helps reproduce factory seam appearance.
Adjust air pressure to control flow. Some guns have adjustable regulators.
Release pressure before changing cartridges. Use the sealer maker's recommended application methods and curing times. Wear gloves and safety glasses, and work with ventilation when sealers contain solvents. Clean the nozzle and gun promptly after use, since cured sealer is hard to remove from the plunger and nose, and store opened cartridges capped to keep them usable.
Tools used for this job
What is an air tire buffer used for?
Short answer: A tire buffer is a low-speed rotary air tool that roughens the inner liner of a tire around a puncture so a patch or plug-patch bonds properly.
Proper tire repair requires preparing the inner liner by buffing to remove the smooth surface and expose fresh rubber. Tire buffers run at low speeds appropriate for this task.
They use buffing rasps, carbide cutters or wire brushes. Follow the tire repair industry's procedures, which call for a combination plug-patch for many punctures.
Wear eye protection and a dust mask. Run the buffer at the speed specified by the repair material maker. Do not repair punctures in the sidewall or shoulder, and do not repair tires with damage outside the industry's repairable area. Clean buffing dust away before applying vulcanizing cement so the patch adheres.
Tools used for this job
How does an air-powered venturi vacuum pump work for A/C service?
Short answer: A venturi vacuum pump runs shop air through a nozzle that creates suction, pulling a vacuum on an A/C system without an electric pump, but it uses a lot of air and usually cannot reach the deep vacuum of a quality electric pump.
Venturi pumps have no moving parts. Compressed air rushes through a narrow passage, and the low pressure created at a side port draws air out of the connected system. They are compact and inexpensive and are useful for quick evacuations or field work where power is limited.
They consume continuous air, so a compressor must keep up for the full evacuation time. Many cannot pull as deep a vacuum as a two-stage electric pump, and they do not have oil to absorb moisture. Check the maker's rated vacuum level and air consumption.
For thorough moisture removal, many technicians prefer an electric vacuum pump and a micron gauge. Never use a venturi pump on a system that still contains refrigerant; recover it first with certified equipment. Wear safety glasses and gloves when connecting to A/C service ports.
Tools used for this job
How does an air-powered coolant vacuum fill tool work?
Short answer: A vacuum fill tool uses shop air through a venturi to pull a vacuum on the cooling system, then uses that vacuum to draw fresh coolant in, filling the system with fewer air pockets.
Air pockets in modern cooling systems can cause overheating, poor heater output and false temperature readings. Vacuum fill tools remove air before coolant is introduced.
Connect the tool to the radiator or reservoir with the correct adapter, apply shop air to pull a vacuum, check that the vacuum holds for leak detection and then open the valve to draw coolant in from a container.
Work only on a cool engine, since hot coolant is under pressure and can cause burns. Follow the vehicle maker's coolant type and bleeding procedure, and wear eye protection and gloves.
Tools used for this job
How does a pneumatic fluid extractor work?
Short answer: A pneumatic fluid extractor uses shop air through a venturi to create vacuum in a tank, which pulls oil, brake fluid or other fluids out through a small probe or hose.
Fluid extractors are used for oil changes through the dipstick tube, removing fluid from reservoirs, and draining differentials or transmissions with fill ports. Pneumatic models build vacuum quickly using shop air, and some can also be pumped by hand.
Warm oil flows faster, but hot fluids can cause burns, so let them cool to a safe temperature. Use the correct probe size and check whether the vehicle maker approves extraction for oil changes.
Do not use extractors for gasoline or other flammable fuels unless the tool is rated for them. Empty and clean the tank after use and dispose of fluids properly. Wear gloves and eye protection.
Tools used for this job
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.