Air Drills, Riveters and Specialty Air Tools
Pneumatic drills, rivet and rivet nut tools, grease guns, needle scalers, slide hammers, caulking guns, windshield tools and other specialty air tools.
What is a pneumatic punch and flange tool?
Short answer: A punch and flange tool punches holes for plug welds and steps a panel edge so replacement panels overlap flush, and air-powered models speed up this body repair work.
When replacing body panels, technicians often create a flange so the new panel sits flush with the existing one. Holes are punched for plug welds.
Air punch and flange tools perform both tasks. They save time and produce consistent results.
Check the tool's rated thickness capacity and keep fingers away from the jaws. Wear eye protection and gloves. Flanging also strengthens the joint and gives a consistent gap for welding or panel bonding. Follow the vehicle maker's body repair manual for where flanged joints and plug welds are allowed, since some structural panels require specific repair methods.
Tools used for this job
How do I change the blades on air shears?
Short answer: Disconnect air, remove the blade retaining bolts, install the correct center and side blades with proper clearance and orientation, then tighten to the maker's specs and test on scrap.
Air shears use a center blade that moves between two side blades. Dull or chipped blades tear metal instead of cutting cleanly.
Always disconnect air before working on the tool. Remove the bolts securing the blades, note orientation and install new blades. Some tools require shims or specific clearances.
Use only blades designed for your tool. Test on scrap, wear eye protection and keep hands clear of the cutting head. Blades that are too loose produce burrs and bent edges, while blades that are too tight bind and stall the tool. Add a drop of air tool oil afterward and run the shears briefly before cutting.
Tools used for this job
What is an air-powered vacuum cleaner kit?
Short answer: An air-powered vacuum kit uses a venturi on shop air to create suction for cleaning interiors, drains and small debris without an electric vacuum.
These kits attach to a container or bag and use compressed air to generate suction. They are useful in shops where outlets are limited or for quick cleanups.
They consume air continuously, so check the compressor's capacity. They work best on light debris.
Do not use them for flammable vapors or liquids unless rated. Wear eye protection when emptying containers. They are often quieter and lighter than small electric shop vacuums, and with no motor they tolerate dusty work. Use clean, dry air to reduce moisture spray from the exhaust, and point the exhaust away from people since it can carry fine dust. Empty the container before it fills to keep suction strong.
Tools used for this job
What is an air angle drill used for?
Short answer: An air angle drill places the chuck at a right angle to the motor, letting you drill in tight spaces such as between body panels, inside door frames and under dashes where a pistol drill will not fit.
Angle drills come with 90-degree or 45-degree heads and are common in aircraft, body and fabrication work. Many use a threaded chuck or a small keyed or keyless chuck.
Because the head is compact, these drills usually have lower torque than full-size pistol drills. They work best with small bits, from about 1/16 inch to 1/4 inch, depending on the model.
Keep bits sharp and use light pressure to avoid stalling or breaking bits in tight spaces. Lubricate the tool as the maker directs.
Wear eye protection and keep fingers clear of the chuck. Clamp small workpieces so they cannot spin when the bit catches.
What is a keyless chuck on an air drill?
Short answer: A keyless chuck lets you tighten and loosen bits by hand without a chuck key, making bit changes faster; heavy-duty keyless chucks on 1/2-inch drills grip well when tightened firmly.
Keyed chucks use a key to apply high clamping force and were traditional on larger drills. Many modern drills use keyless chucks with ratcheting or locking mechanisms.
For large bits and high torque, tighten the chuck firmly by hand and check that the bit is centered.
If bits slip, clean the chuck jaws and inspect them for wear. Replace worn chucks with the correct thread and size.
Disconnect the air supply when changing bits, wear eye protection and use side handles where provided.
Tools used for this job
What is a pneumatic tapper used for?
Short answer: A pneumatic tapper drives taps quickly and reverses automatically or at the push of a lever, letting fabrication shops cut many threaded holes faster and with less tap breakage than by hand.
Tappers use a reversible air motor, often with a clutch or torque limiter to reduce tap breakage. Some mount on articulating arms that keep the tap square.
They are used for production threading in plate, brackets and frames. Use proper tapping fluid and the correct drill size.
Taps break if forced or misaligned, so keep the tool square and let it reverse to clear chips.
Wear eye protection, clamp workpieces and disconnect air before changing taps. Check the tapper's rated tap size range before buying.
What is an air screwdriver and how do I set its clutch?
Short answer: An air screwdriver drives screws using an air motor with an adjustable clutch that slips or shuts off at a set torque, preventing stripped heads and overtightening in assembly work.
Air screwdrivers are common in assembly lines, interior trim and electronics work. They come in pistol and straight styles.
Clutch settings are adjusted with a spring and collar per the maker's instructions. Start low and increase until screws seat properly.
Shutoff clutches stop the motor at torque, offering better consistency than cushion clutches that slip.
Keep bits matched to screw heads, wear eye protection and disconnect air before adjustment. Verify settings with a torque tester when the job has a specified torque. Recheck after changing air pressure, since output can shift.
What is a pneumatic valve lapping tool?
Short answer: A pneumatic valve lapping tool uses an air motor to oscillate or rotate a suction cup holding the valve, speeding up lapping the valve face to its seat with lapping compound, compared with spinning a hand stick between your palms.
Valve lapping blends the valve face and seat for a uniform seal after machining or when checking a seat. Traditionally it is done with a wooden stick and suction cup spun by hand, which is slow on engines with many valves.
Air lappers mimic that back-and-forth motion. They let the technician focus on light pressure and frequent lifting so the compound redistributes.
Lapping is not a substitute for proper valve and seat machining, and some modern engines and coated valves should not be lapped, so follow the engine maker's guidance.
Clean every trace of lapping compound from the head and valves afterward, since it is abrasive and will damage the engine. Wear eye protection and gloves.
What is a pneumatic hog ring plier?
Short answer: A pneumatic hog ring plier uses air to close hog rings automatically, making it much faster and easier on the hands to attach seat covers, upholstery and fencing than squeezing rings closed with manual pliers.
Automotive upholstery uses hog rings to fasten covers to seat frames and listing wires.
Air tools close each ring with consistent force, reducing hand fatigue during seat jobs.
Use the correct ring size for the tool.
Keep fingers clear of the jaws, disconnect air when clearing jams and wear eye protection. Some models feed rings from a magazine, while others are loaded one ring at a time. Set air pressure so rings close fully without cutting the fabric or crushing the wire. Practice on scrap material before working on a finished cover, and keep the tool oiled as the maker directs so the jaws close smoothly.
What is an air scribe or pneumatic engraver?
Short answer: An air scribe uses a small, fast reciprocating carbide tip powered by compressed air to engrave marks, part numbers and identification on metal, and it is also used in fossil preparation and stone work.
Shops use air scribes to mark tools and parts for identification.
They need low air volume but clean, dry air.
Control depth by pressure and tip angle.
Wear eye protection and hearing protection, and secure the workpiece. Some air scribes have adjustable stroke and speed for fine or heavy work, and many are light enough to use like a pencil for long periods. Carbide tips wear and can be resharpened or replaced. Oil the tool as the maker directs and use a filter so moisture does not reach the small piston. Marking tools with an owner identifier helps track them in shared shops and deters theft.
How do I drill stainless steel with an air drill?
Short answer: Drilling stainless steel with an air drill works best at low speed with steady, firm pressure, sharp cobalt bits and cutting fluid, because stainless work-hardens quickly if the bit rubs instead of cutting.
Stainless steel heats up and hardens at the cutting edge when a drill bit spins too fast or with too little feed. Once it hardens, a dull or slow bit just polishes the surface.
Use a slower air drill, or feather the throttle, and keep consistent pressure so the bit always cuts a chip. Cobalt bits are a common choice for stainless, and a split-point tip helps start without walking.
Apply cutting oil or fluid generously, and back out to clear chips on deeper holes. A small pilot hole can help on larger sizes.
Clamp the workpiece, wear eye protection and gloves when handling sharp chips, and never hold small parts by hand while drilling.
Tools used for this job
Can I use left-hand drill bits in a reversible air drill to remove broken bolts?
Short answer: Yes, a reversible air drill running in reverse with left-hand drill bits is a common way to remove broken bolts, because the cutting torque can catch and back the broken piece out before an extractor is needed.
Start by center-punching the exact center of the broken bolt so the bit does not wander into the threads. Use a left-hand bit smaller than the bolt's minor diameter.
Run the drill in reverse at low speed with steady pressure. Often the bolt breaks loose and spins out as the bit bites.
If it does not, a screw extractor may be needed, used carefully to avoid breaking it off in the hole.
Wear eye protection, use penetrating oil and apply heat only when it is safe around nearby components.
What is a pneumatic nutrunner?
Short answer: A pneumatic nutrunner is an air tool designed for repeatable tightening on production lines, using a clutch or shutoff mechanism that stops at a set torque, so it delivers more consistent results than an impact wrench on assembly work.
Nutrunners come in straight, pistol and angle styles. Unlike an impact wrench, they rotate continuously and shut off when they reach the preset torque, which reduces operator variability.
They are common in automotive assembly, appliance manufacturing and other production settings where many fasteners need the same torque.
Reaction torque can be significant on larger models, so torque arms or reaction bars are often used. Regular calibration keeps them accurate.
In repair shops, torque-critical fasteners are still checked with a calibrated torque wrench. Wear eye protection and keep hands clear of rotating sockets.
General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.