Store relaunching soon · pro diagnostics & tools for independent shopsjoseph@directtoolsource.com
Direct Tool SourcePro Diagnostics
Home / Answers / Air Tools & Compressed Air / Pneumatic Nailers, Staplers and Riveters

Pneumatic Nailers, Staplers and Riveters

Air-powered fastening tools, how they work and how to use them safely.

17 answers · last reviewed 2026-11-20

How does a pneumatic nail gun work?

A pneumatic nailer uses compressed air stored in the tool's handle to drive a piston and blade that strike the nail, with a valve system triggered by the trigger and the contact nose.

Read the full answer →

What is the difference between sequential and contact trip nailers?

Short answer: A sequential trigger requires the nose to be pressed against the work before pulling the trigger for each nail, while a contact or bump trigger fires whenever the nose is bumped with the trigger held, which is faster but has a higher injury risk.

Safety research and workplace guidance have found that contact trip triggers are associated with more unintended firing injuries. Some employers and guidelines recommend sequential triggers, especially for less experienced users.

Many nailers come with a sequential trigger or a selectable trigger. Check the tool's manual for how to change modes.

Sequential mode is slower for repetitive work like sheathing, but reduces double fires and accidental discharges.

Regardless of mode, keep your finger off the trigger when not nailing, wear eye protection and keep your hand clear of the nailing path.

What is a pneumatic upholstery stapler used for in auto work?

Short answer: Pneumatic upholstery staplers drive fine-wire staples into seat frames, headliners and trim panels, making interior and upholstery work faster and neater than manual staplers.

Auto upholstery shops use them to attach fabric and vinyl to seat bases, door panels and boat seats. They use narrow crown staples in various leg lengths.

Choose a stapler and staple size that matches the material and the backing. Long staples can poke through thin panels.

Use low pressure for delicate materials and adjust depth to avoid tearing fabric. Disconnect air before clearing jams.

Wear eye protection and keep fingers away from the nose. Staples can ricochet off hard surfaces.

How do I choose between air and hand rivet tools?

Short answer: Hand riveters are fine for occasional jobs and small rivets, while pneumatic riveters save fatigue and time on repetitive work, larger rivets and stainless rivets that are hard to pull by hand.

Hand riveters are portable and need no air supply. They work well for a few rivets in aluminum or steel.

Air riveters pull rivets quickly with less effort, which reduces hand strain in trailer, body and fabrication work. Many collect spent mandrels in a container.

Check the riveter's capacity for rivet diameter and material. Rivet nut tools are separate or use special adapters.

Wear eye protection, since mandrels can fly out, and disconnect air before changing nosepieces. Oil air riveters as the maker directs and empty the mandrel collector before it overfills.

Tools used for this job

Astro Pneumatic PR14 1/4"Air Rivet ToolAstro Pneumatic PR36 3/16"Air Rivet ToolAstro Pneumatic 1423 Heavy Duty 13" Hand Riveter

How do I clear a jam in a pneumatic nailer?

Short answer: Disconnect the air supply, remove the nails from the magazine, open the nose latch if the tool has one and remove the bent fastener with pliers, then inspect the driver blade before reconnecting.

Jams happen with wrong-size nails, bent strips, worn driver blades or low air pressure. Never try to clear a jam with the air connected.

Many nailers have tool-free jam release latches. Remove the fastener carefully and check the nose for damage.

If jams repeat, check that you are using the right fastener type, lubricate the tool as the maker directs and inspect the driver for wear.

Wear eye protection and keep hands clear when reconnecting air. Test fire into scrap wood.

What is a pneumatic brad nailer used for?

Short answer: A pneumatic brad nailer drives thin 18-gauge brads for trim, molding, cabinet backs and small woodworking projects, leaving small holes that are easy to fill and holding light pieces while glue dries.

Brads are thin enough that they rarely split narrow trim or thin stock, which makes the brad nailer one of the most popular first nail guns for home shops. Common lengths run from about 5/8 inch to 2 inches, depending on the tool.

Because the fastener is thin, holding power is limited. Brads work best for light trim, glue-ups and decorative pieces rather than structural joints or heavy baseboard on uneven walls.

Brad nailers use little air, so a small pancake compressor can run one easily. Set the depth adjustment so the head sits just below the surface for filling.

Wear eye protection, keep your free hand well away from the nose, disconnect air when clearing jams and never point a nail gun at anyone.

What is the difference between a finish nailer and a brad nailer?

Short answer: A finish nailer drives thicker 15- or 16-gauge nails with more holding power for baseboards, door casing and heavier trim, while a brad nailer uses thinner 18-gauge brads that leave smaller holes but hold less.

Finish nails are larger in diameter and usually available in longer lengths, often up to about 2-1/2 inches. That makes them better for attaching trim through drywall into framing.

Brad nailers are better for delicate molding and thin stock that a finish nail might split.

Some finish nailers are angled, which helps reach into corners and uses angled collated nails.

Many trim carpenters own both. Whichever you use, wear eye protection, keep fingers away from the firing path and use the sequential trigger mode for precise placement.

What is a pneumatic pin nailer?

Short answer: A pneumatic pin nailer drives very fine 23-gauge headless pins that leave almost invisible holes, making it ideal for holding small moldings, veneers and glued parts where appearance matters more than holding strength.

Pin nails are so thin they usually do not need filling, and they are unlikely to split delicate pieces. They mainly hold parts in position while glue cures.

Because they are headless, pins have very little pull-through resistance on their own, so they are not a replacement for brads or finish nails on structural trim.

Pin nailers use very little air and run fine on small compressors. Some have adjustable power to avoid blowing pins through soft wood.

Pins can deflect off hard grain and exit sideways, so keep your hand clear of the work near the nose and wear eye protection at all times.

What is a pneumatic framing nailer and what nails does it use?

Short answer: A pneumatic framing nailer drives large nails, typically around 2 to 3-1/2 inches, for wall framing, decks and sheathing, using strip nails collated in plastic, paper or wire at angles that vary by tool, so nails must match the nailer's collation and angle.

Framing nailers come in several collation styles, including 21-degree plastic strip, 28-degree wire weld and 30- to 34-degree paper tape. The angle and collation must match the tool.

Some local codes restrict clipped-head nails, so check requirements before buying nails or tools.

Framing nailers use more air than trim guns and benefit from a compressor with higher delivered CFM, especially when more than one runs at a time.

They have strong recoil. Use the sequential trigger when precision matters, keep both feet stable, never carry the tool with a finger on the trigger and wear eye and hearing protection.

What is a pneumatic roofing nailer?

Short answer: A pneumatic roofing nailer drives short, wide-head coil roofing nails through asphalt shingles quickly, with an adjustable depth setting so nails sit flush without cutting through the shingle, which is critical for weather resistance.

Roofing nailers use coils of wire-collated nails, which hold many fasteners and reduce reloading on the roof.

Correct depth matters. Overdriven nails cut into the shingle and can let water in or cause blow-offs, while underdriven nails can cause bumps.

Follow the shingle maker's nailing pattern and count.

Roof work involves fall hazards. Use fall protection, secure hoses so they do not pull you off balance, wear eye protection and never point the nailer toward others. In cold weather, shingles become brittle and nailers may need slightly different depth settings, so test on a scrap piece first.

What is a narrow crown stapler used for?

Short answer: A narrow crown pneumatic stapler drives staples with a crown of about 1/4 inch for cabinet backs, drawer bottoms, trim and upholstery, where staples hold better than brads on thin panels.

The staple's two legs and crown resist pull-through better than a single brad.

Wide crown staplers handle sheathing and housewrap, while fine-wire staplers suit upholstery.

Match the staple gauge and crown width to the tool.

Wear eye protection, keep fingers clear of the nose and disconnect air before clearing jams. Narrow crown staplers are also handy for attaching cardboard templates, insulation backing and plastic sheeting in the shop. They use little air, so a small compressor runs one easily. Check the maker's guide for maximum staple length, and set depth so the crown sits flush without tearing thin material.

Why does my nail gun leave nails sticking up?

Short answer: Nails that stand proud usually mean the depth adjustment is too shallow, the air pressure is too low at the tool, the wood is too hard for the nail length, or the driver blade and bumper are worn.

Start with the depth adjustment, then increase pressure gradually within the tool's rating.

Check hose length and coupler size for restrictions.

Worn bumpers or driver blades reduce drive depth over time and can be replaced.

Never set nails with a hammer while the nailer is connected and pointed at your hand, and wear eye protection. Using nails that are too long for the tool's power, or driving into dense hardwood, knots or metal straps, also leaves heads proud. Try a shorter nail or a pilot location away from knots. A dry tool can also lose power, so add a few drops of air tool oil if the maker calls for it.

Why does my nail gun double fire?

Short answer: Double firing happens when a nail gun's recoil bounces the contact tip back against the work in contact trip mode, or when worn trigger or valve parts cause the tool to cycle twice, which is both a safety hazard and a cause of wasted or misplaced nails.

In contact trip mode, holding the trigger while recoil lifts and drops the tool can fire a second nail. Firm grip and sequential mode reduce this.

Worn O-rings in the trigger valve or a damaged head valve can also cause repeat firing.

Stop using a tool that fires unexpectedly and have it repaired.

Wear eye protection and keep hands clear of the work near the nose. A dirty or sticky trigger assembly can also cause erratic behavior. Clean and lubricate as the maker directs, and replace worn parts with a rebuild kit.

What is a pneumatic flooring nailer?

Short answer: A pneumatic flooring nailer drives cleats or staples at an angle through the tongue of hardwood flooring when struck with a mallet, pulling boards tight and hiding the fastener, and it needs the correct base plate for the floor thickness.

Flooring nailers sit on the edge of the board, and a rubber mallet strike on the plunger fires the fastener through the tongue at about 45 degrees. Air assists the drive so each fastener seats consistently.

Use the fastener type and size the flooring maker recommends, either L-shaped cleats or staples. Using the wrong fastener can split tongues or cause squeaks.

Adapter plates adjust the tool for different board thicknesses so fasteners enter at the right spot.

Set pressure as the tool maker suggests and test on scrap. Wear eye and hearing protection and knee pads, and keep fingers away from the nose.

What is a pneumatic palm nailer?

Short answer: A palm nailer is a small air tool that fits in the hand and drives loose nails with rapid hammer-like blows, making it useful for joist hangers, metal connectors and tight spots where a full nailer or hammer will not fit.

Palm nailers accept individual nails held in a magnetic nose, so they work with the specific connector nails that hangers require.

They are compact enough to work between framing members.

They are noisy and vibrate, so limit continuous use.

Wear eye protection, hearing protection and gloves, and keep fingers clear of the nose while it is cycling. Some palm nailers are strapped to the hand, while others have a small handle. Mini versions handle small finish nails for trim, and larger models drive framing nails. Because the tool hammers repeatedly until the nail is seated, practice controlling it so you stop right when the head is flush.

General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.