Store relaunching soon · pro diagnostics & tools for independent shopsjoseph@directtoolsource.com
Direct Tool SourcePro Diagnostics
Home / Answers / Air Tools & Compressed Air / Filters, Regulators, Lubricators and Dryers

Filters, Regulators, Lubricators and Dryers

Cleaning, drying and regulating shop air: FRL units, coalescing filters, refrigerated and desiccant dryers.

32 answers · last reviewed 2026-11-20

What is an FRL unit for compressed air?

An FRL is a filter, regulator and lubricator assembled in series; it removes water and dirt, sets the pressure your tools need and adds a fine oil mist for tools that require lubrication.

Read the full answer →

Do I need an air dryer for my shop?

If water shows up in tools, hoses or paint, or your air lines run through cold areas, a dryer is worthwhile; refinishing and paint work almost always need one.

Read the full answer →

What is the difference between a refrigerated and desiccant air dryer?

Short answer: Refrigerated dryers cool air to condense water and suit general shop use, while desiccant dryers absorb moisture to reach much lower dew points and suit paint and critical applications.

A refrigerated dryer works like a small refrigerator. It chills compressed air to a low temperature, condensing water that drains away, then reheats the air before it leaves. Typical pressure dew points are a few degrees above freezing, which prevents condensation in lines kept above that temperature.

Desiccant dryers pass air through material that adsorbs water vapor. They achieve far lower dew points, so air stays dry even in cold lines. Point-of-use desiccant units are popular at paint guns. Larger regenerative desiccant dryers use some compressed air to dry their beds.

Many shops use a refrigerated dryer for the whole system and a desiccant unit at the paint booth. Replace or regenerate desiccant on the maker's schedule. Follow electrical and installation instructions, and depressurize dryers before service.

Tools used for this job

DeVilbiss 130500 Desiccant Air Dryer System CT-30DeVilbiss 130546 DAD-PRO™Desiccant Air Drying System

What is a coalescing air filter?

Short answer: A coalescing filter captures fine oil aerosols and water droplets by merging them into larger drops that drain away, and it is used downstream of a general filter for paint and clean-air applications.

General particulate filters remove dirt and larger water droplets but let fine oil mist pass. A coalescing filter uses a dense fiber element where tiny droplets collide and merge, then drain to the bowl.

Coalescing filters are essential where oil contamination is unacceptable, such as painting, sandblasting and some pneumatic controls. They are usually installed after a particulate pre-filter so the fine element is not clogged by dirt.

Pressure drop increases as the element loads, so replace elements on schedule or when a differential gauge indicates. Drain the bowl regularly. Use a bowl guard and depressurize before changing elements, wearing eye protection.

Tools used for this job

Milton 1019 3/8 Micro Filter with Poly Bowl and GuardDeVilbiss 803643 80 CFM Air Filter Cleaner with Regulator HAR680

How do I set an air pressure regulator correctly?

Short answer: Set the regulator while air is flowing to the tool, adjusting until the gauge or an inline gauge at the tool reads the tool's rated pressure, then lock the knob.

Regulators reduce line pressure to a steady output. Setting them with no flow gives a static reading that will drop when the tool runs.

Pull the regulator knob out to unlock it. Run the tool or open a blow gun to create flow, and turn the knob until the gauge reads the desired pressure. For most air tools, that means about 90 PSI at the tool inlet. For greater accuracy, use an inline gauge at the tool. Push the knob in to lock.

When reducing pressure, turn the knob down and then bleed air downstream, since some regulators do not vent on their own. Never exceed the tool's maximum rated pressure. If you cannot reach the target under flow, the regulator or supply may be too small.

Tools used for this job

Milton 1145S 1/4 NPT Mini Heavy Duty RegulatorMilton 1113 1/4 Regulator NPTS&G Tool Aid 98000 Aluminum Air Regulator

How often should I drain my air filter bowl?

Short answer: Drain filter bowls daily in busy or humid shops, or whenever liquid is visible, because a full bowl lets water pass downstream; automatic drains help.

Filter bowls collect water, oil and debris removed from the air. If the bowl fills above its baffle, water can be swept back into the air stream.

Most bowls have a manual drain at the bottom, either a twist valve or a push button. Open it with pressure on to purge collected liquid. Some filters have semi-automatic drains that open when pressure drops, or float drains that operate automatically.

Check bowls at least daily in humid weather and drain as needed. Replace elements when pressure drop increases. Inspect plastic bowls for crazing or cracks and replace damaged bowls immediately. Always keep bowl guards installed and depressurize before removing a bowl.

Tools used for this job

Milton 1018 1/4 Micro Filter Poly Bowl and GuardMilton 1018-8 1/4 Micro Filter Heavy Duty Metal Bowl NPT

Are plastic filter bowls safe?

Short answer: Plastic polycarbonate bowls are safe when used within their pressure and temperature ratings with a bowl guard, but solvents and some compressor oils can weaken them, so metal bowls are safer in harsh environments.

Polycarbonate bowls let you see collected water, which is convenient. However, some chemicals, including certain solvents, cleaning products and synthetic compressor oils, can attack polycarbonate and cause cracking. A cracked bowl can burst under pressure.

Use a metal bowl guard on plastic bowls, and inspect bowls for crazing, clouding or cracks. Never clean plastic bowls with solvents unless the maker approves. Replace damaged bowls immediately.

Metal bowls with sight glasses are available for harsher conditions and higher temperatures. They resist chemical attack and impact. Choose metal bowls near compressors where air is hot, or in areas with solvent exposure. Depressurize before removing any bowl.

Tools used for this job

Milton 1018-8 1/4 Micro Filter Heavy Duty Metal Bowl NPTMilton 1022-8 3/4 Micro Filter Metal Bowl Heavy Duty 10 Oz

What micron filter rating should I use for air tools?

Short answer: General air tools are well served by filters in the range of about 5 to 40 microns, while paint and sensitive equipment need finer filtration and coalescing elements.

Filter ratings describe the smallest particle size the element is designed to capture. Finer ratings remove more contaminants but clog faster and create more pressure drop.

For impacts, ratchets and grinders, a general-purpose particulate filter protects tools from rust and debris. For paint guns and sandblasters, a coalescing filter and dryer remove oil aerosols and fine water.

Check the filter maker's specifications for pressure drop at your flow rate. Replace elements when they restrict flow. Install filters before regulators and lubricators. Depressurize and wear eye protection when changing elements.

Tools used for this job

Milton 1018 1/4 Micro Filter Poly Bowl and GuardMilton 1019 3/8 Micro Filter with Poly Bowl and Guard

How do I set an air line lubricator?

Short answer: Fill the lubricator with air tool oil, run the tool and adjust the drip rate to the maker's recommendation, often a drop or two per minute or per a set volume of air.

Inline lubricators add oil mist to the air for tools that need continuous lubrication, such as some production tools. They must be installed after the filter and regulator and close to the tool.

Depressurize, fill the bowl with air tool oil, and reinstall it. Run the tool at normal flow and watch the sight dome. Adjust the needle valve so oil drips at the rate the tool maker or lubricator maker recommends. Too much oil sprays out of the exhaust; too little leaves tools dry.

Do not use a lubricator on lines feeding paint guns, blow guns, inflators or air-operated equipment that should be oil-free. Check the oil level regularly, and use a bowl guard. Wear eye protection when adjusting.

Tools used for this job

S&G Tool Aid 98500 Air Tool OilerS&G Tool Aid 98800 1/4"NPT Large OilerMilton 1001-16 16 Oz Air Tool Oil

Should I use an inline oiler or oil tools by hand?

Short answer: Many shops oil tools by hand with a few drops daily because it keeps oil out of shared lines, while inline oilers suit dedicated tool stations and production tools.

Inline lubricators provide continuous oil to tools on a dedicated line, which suits production environments. In a repair shop, however, the same line may feed blow guns, inflators and tire machines, which should not receive oil.

Manual oiling, adding a few drops of air tool oil into the tool inlet before use, gives precise control and keeps lines clean. Some makers recommend this method. Small inline oilers that attach at the tool are a middle option.

Follow each tool maker's lubrication instructions. Some modern tools have lubrication-free motors. Never add oil to lines feeding paint or blast equipment. Wipe excess oil from tool exhausts to avoid slippery floors.

Tools used for this job

Milton 1001-4 4 Oz Flip Top Air Tool OilS&G Tool Aid 98500 Air Tool Oiler

What is a water separator and do I need one?

Short answer: A water separator uses centrifugal action and a baffle to spin liquid water out of the air stream and collect it, protecting tools; it is a good first stage near drops and compressors.

Water separators remove liquid water and larger particles. Air enters and is spun by vanes, throwing water against the bowl wall where it drains. A baffle keeps collected water from re-entering the air.

They do not remove water vapor, so air can still condense downstream. Pair them with a dryer for better results. Separators are often combined with a particulate filter element.

Install them before regulators and lubricators, and drain them regularly. Point-of-use separators protect tools from water that forms in hoses. Depressurize and wear eye protection before servicing.

Tools used for this job

S&G Tool Aid 99000 In-Line Water Separator and Air FilterMilton 1018 1/4 Micro Filter Poly Bowl and Guard

How do I know when to replace an air filter element?

Short answer: Replace the element when pressure drop across the filter increases noticeably, when it looks clogged or discolored, or at the maker's interval.

A clogged element restricts air and lowers tool performance. Many filters have a differential pressure indicator that shows when the element is loaded. Without one, compare pressure before and after the filter under flow.

Visual inspection also helps. Elements darkened with rust, oil or dirt need replacement. Coalescing elements should be replaced on schedule even if they look clean, since saturation reduces effectiveness.

Keep spare elements on hand. Depressurize before removing bowls, clean the bowl with soap and water rather than solvents, and inspect seals. Wear eye protection when opening filters.

Tools used for this job

Milton 1018 1/4 Micro Filter Poly Bowl and GuardMilton 1019 3/8 Micro Filter with Poly Bowl and Guard

What is a pressure dew point?

Short answer: Pressure dew point is the temperature at which water vapor in compressed air begins to condense at system pressure; a lower dew point means drier air.

Air holds a certain amount of water vapor depending on temperature and pressure. When compressed air cools below its pressure dew point, water condenses.

Refrigerated dryers typically achieve pressure dew points a few degrees above freezing. Desiccant dryers can achieve far lower dew points, keeping air dry even in freezing lines.

Choose a dryer whose dew point is below the lowest temperature your air lines will see. If lines run through cold areas, a refrigerated dryer may not be enough. Consult dryer makers for sizing at your conditions, and follow their safety instructions for installation.

Tools used for this job

DeVilbiss 130500 Desiccant Air Dryer System CT-30

Do I need a separate air setup for painting?

Short answer: Yes, paint needs clean, dry, oil-free air, so use a dedicated drop with a coalescing filter, a dryer and a regulator, and no lubricator.

Paint defects like fisheyes, blushing and contamination often come from oil or water in the air. Lubricated tool air can carry oil mist that ruins finishes.

Set up a dedicated drop for painting. Include a particulate filter, a coalescing filter for oil aerosols, and a dryer, often a desiccant unit. Use a regulator and gauge at the gun. Keep a dedicated hose that never carries lubricated air.

Maintain the system by draining filters and replacing elements and desiccant on schedule. Use a respirator rated for the coatings you spray and ensure booth ventilation. Many paints contain isocyanates, which require proper respiratory protection.

Tools used for this job

DeVilbiss 130546 DAD-PRO™Desiccant Air Drying SystemDeVilbiss 803643 80 CFM Air Filter Cleaner with Regulator HAR680S&G Tool Aid 98300 Air Adjustment Valve for Paint Spraying with Gage

What size regulator do I need for air tools?

Short answer: Choose a regulator whose flow rating exceeds your tools' CFM with minimal pressure drop; small 1/4-inch regulators can restrict high-demand tools, so 3/8-inch or larger ports are often better.

Regulators are rated by port size and flow capacity. A regulator that is too small causes a pressure drop under flow, so the tool sees less pressure than the gauge suggests.

For general air tools, regulators with 3/8-inch ports are common at drops. For high-demand tools, choose a regulator rated for higher flow. The maker's flow chart shows pressure drop at various flows.

Install the regulator after the filter. Set it under flow. If tools still feel weak, measure pressure at the tool to check whether the regulator is limiting flow. Depressurize before replacing any regulator.

Tools used for this job

Milton 1145S 1/4 NPT Mini Heavy Duty RegulatorAstro Pneumatic 2615 3/8" Filter/Regulator with Gauge

General guidance only. Follow the vehicle and tool manufacturer's procedures, and confirm vehicle coverage on the tool maker's list before buying.